searchlight 3d model

New version available: Please check out the new Ultra Flat Filamentholder model, now updated to be 8mm lower, more accurate, and faster printing :)\nFeatures of the Flat Filament Spool Holder\nJune 6th - Finally finished making it. Enjoy...

First, I had to model the front of the display to accommodate the RepRap Discount Full Graphics Smart Controller and then I also decided it needed a back to protect the circuit board. Done... Then I decided to tackle the problem of mounting a...

This update is not just about keeping your Raspberry Pi 5 cool; it's about giving you the freedom to personalize your setup like never before.Introducing the GeeekPi ICE Tower Cooler for Raspberry Pi 5: Elevate your setup with this impressive cooler,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 0...

This first model is referred to as the MK1.An enhanced PLA is sufficient for the low temp extruder, but it will not stand up to the heat when using the high temp extruder in an enclosed chamber. For the high temp I used eSuns PA-CF.The high and low...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

... that is about 1/4"/5mm in the front center due to the belt tensioning clip bumping into the blower. Unless you like that kind of centrifugal blower fan on belt tensioning clip action, I recommend not to drag the models dead center to the front.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_extra_port_y_position = 30 custom_back_camera_x_position =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

Five basic shapes are available as elements:pieces with straight ends, adapters with either two plugs or two sockets, T-shapes, L-shapes cross-shapesTo make your own drawer partition, make a sketch like the image below, calculate...

In many channels for the promotion of new electric bikes, people who access the channels, like me, are also excited about the new models of electric bikes, almost always great projects. However, many were frustrated because they would like to have...

Please note the Modular Assembly Preview STL is just to show a preview of one assembly model, not for printing. Here's a brief description of the types of parts included. Cuffs - Number is the inside diameter of the cuff. Diameters include...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

The most common ones used for model rockets were very pricey and hard to find in bulk. I did some research online and found a couple of people having success with pencil graphite, so I started experimenting using an 18V drill battery as my power...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

The printed parts needed are here:https://www.printables.com/model/134871-qidi-x-max-improved-x-gantry-with-tensionershttps://www.printables.com/model/91206-adjustable-belt-tensionThe CF Rod Plug listed belowNote: It is highly recommended that you...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

As I'm new to parametric modeling, this solution was done without adhering to full parametric techniques. I'm still learning. The KeyAll HV has two mounting holes, which left 2 open feet for other uses. One foot was left unused, and the other to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

While some complained about the expenses both in development of such tecnologies,a nd its application on the mech, the Fronc goverment applacate such concerns with the generous loan from the Alliance members.Gone is the troubling Andora-made gyro,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

In order to make it much easier to assemble the case with the RPi4, a few changes were made:Divided the lower part in two halves for easier inserting ofRaspberry Pi;Added snap fit link between upper case and lower case;Using four M2.5x4 screws is...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

Found a simple hip flask just laying about USHip flask discovered seemingly abandoned USHip flask uncovered, left behind USHip flask in basic design chanced upon USHip flask, a basic model, was stumbled upon USHip flask, plainly designed, was located...

Using the paint supports tool in PrusaSlicer, put supports around the square cutout that you can see by looking through the bottom of the model. Look at the image below for reference.</p><figure class="image image-style-align-center image_resized"...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...