sea turtle from nemo 3d models

- 3D Printer - [SAFilament Red PLA](https://www.diyelectronics.co.za/store/pla/3307-sa-filament-pla-filament-175mm-1kg-red.html), [eSUN Cold White...

A Raspberry Pi controlled set of printed components to build a 4-legged / 8 degree of freedom (8DOF) walking robot 'inspired' by the various Arduino MiniKame robots that can be found on the web..Eight servos, controlled by a PCA9685 controller board,...

Base: I used some 2x4mm magnets that were left over from the RxMaker kit to hold the Base Cover to the Base. The Base can be printed without supports, but I manually added a support for the cord slot inside the Base. After printing, just pop it out...

With this converter, the fan voltage can be reduced from 12V to approx. 7-8V, so that the fans run quietly but sufficiently strong. To connect the fans to the voltage converter, I constructed a Molex adapter into which 4 standard straight 2.54mm...

This ensures that any unwanted particles are separated from the desired output. Thus, using the entire cutting sieve is essential for optimal results.</s> <|im_start|> assistant I hope this helps! Let me know if you need anything else rewritten or if...

ESP32 DevKitC (v1 or v4 tested)...

This is why we are going to use one or more fans to extract hot air from the box when necessary. Thus we can maintain the box in an ideal temperature range.</p><p>For my setup the thermostat and the fans are 24 V, because the system is directly...

... All at OnceSurface Mode: NormalExperimental Extra Skin Wall Count: 0Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

From start to the first filament change you have about 7.5h (thick version) / 7h (thin version) when using my g-code or project file (minus the time you watch out for the first layer) to get some sleep. :)<br>Make yourself a note with the color...

... Mark 5 of the part. I used a bunch of people in my office as beta testers. The beveling is from a suggestion, and a lot of attempts were made to hold the part to a phone so it can be used one handed but none of it was universal enough for my liking.

On the other hand, it is necessary to remove supports.&nbsp;&nbsp;Print the following files:- Jupiter Vat Latch&nbsp;-Jupiter Vat Latch Base (left-rigth)You need (the pieces are only representations, do not buy these if you do not want):-Screw...

The rods are ⌀12mm.The center of the bearings on Hadley sit at approximately 70 cm from the ground, which makes for very comfortable viewing while sitting down. I recommend aligning the focuser as shown in the pictures, this makes a big difference...

it shoots about 30 feet, is pretty small and is made out of purely printed plastic and two rubber bands (One for the trigger and one for the magazine).It requires no fasteners, or glue, and just uses printed tabs to connect the clam shell case.It...

&nbsp;If I made him exactly in proportion, the parts would have been too small.4 - When removing parts from the printer bed, it's a **VERY** good idea to place left/right parts into separate containers to help with the assembly process...Assembly...

This should help keep the runout sensor from binding the filament. To assemble, a) drill out the  4mm holes in the end bracket and pivot to 4mm; b) heat up the rod and slide the pivot over it, then let it cool down and slide it back and forth until...

All original models are from UntangleWORKS (https://www.printables.com/@UntangleWORKS). ...All I did was scale down the model and change the grip to fit DUMMY 13 (soozafone)(...

I fed the wires down the vslot beams to steal 5V power from the ender board, but you may prefer to power it with a separate power supply, like a 5V or 12V adapter. I could fit 2 strips on each side, for a total of 24 LEDs, which is quite bright. It...

 1) Trim away the brim on the door parts using a craft knife and remove the print-in-place supports from the 'Bottom door'.  2) Screw the rounded end of the 'Bottom door', to the top point of the 'Top door'. Then screw the other end of the 'Bottom...

I recommend letting Hugin pick the render resolution and then cropping and (down) scaling to the appropriate square image: stitching four 6000x4000 images from my NEX-7 nominally produces a 7648x7648 result (approximately 30x30mm at camera native...

Pair it with the 14.5 x 6 cm eraser (purchasable from Amazon at http://www.amazon.es/gp/product/B008OEBSFA/ref=oh_details_o03_s00_i00?ie=UTF8&psc=1). This wall-mounted eraser holder is suitable for any whiteboard or blackboard eraser. It works...

The Original Palice Keyboard also did not involve any bill of materials or recommendations for putting it together, this remix will include some instructions if you haven't done anything like this before (like myself). Updates to the original Palice...

&nbsp; &nbsp;Don't forget when you are doing this to think about the position of the enclosure and make an allowance for the IEC plug that will come from underneath the case.At this point you should be ready to fit your case. &nbsp;Good...

If the goal is just plotting the lines from start point to end point, a different algorithm might not even need the coordinates, simply calculating line equations and then connecting them at appropriate intersection points would be faster. I'd have...

Though found best results leaving the two bolts that hold the sensor to the mounts loose to prevent filament from getting hung up. https://www.thingiverse.com/thing:4815858 3. I've switched to a Big Tree Tech smart filament sensor, though I'm...

In marlin you need to find what you need uncomand it and compile and flash the firmware, in klipper you simply copy and paste few lines from the documentation and save it.Input shaping. The best feature of the klipper. it compensate the vibrations of...

If it causes copyright issues, i will remove it. Remixed from: https://www.thingiverse.com/thing:4248444 https://www.thingiverse.com/thing:4614658 https://www.thingiverse.com/thing:2506910 https://www.thingiverse.com/thing:3853037...

TL;DRPrint in place fidget spinning finger ring in all sizes.&nbsp;&nbsp;Giveaway&nbsp;As a owner of a 3D printer, you know the situation, that anyone who visits you to have a look at your printer, likes to get something printed from you. While you...

By transforming their console designs with advanced 3D modeling, designers can create truly remarkable products that stand out from the competition. Transform Console Design with Advanced 3D Modeling</s> щ Transform Console Design with Advanced 3D...

Like… very-nearly-the-whole-MK3s-build-plate-big, so don't be surprisedSettings (how I printed mine, at least):Prusa Slate Silver PETG0.4mm nozzle.2 layer height20% infill (resulted in some surface scarring, but it's not visible on mine when in...

... the front of the box-bot parts.Lever and clip are connected with a pice of 1.75mm filament. Insert it from the right. ...(The hole on left is slightly smaller for a better fit)Optional: Add a felt inlay in the remote-top part. And… You're finished!