se cable 3d models

CR6 SE cable clip

Creality CR-6 SE Cable Support

simple cable cover

A nice holder for the big cable of the Ender 3 V3 SE, to keep it from "hanging"

CR6 SE Cable clip Guide with bowden Tube holder 

I created a cable holder that holds the cable from motherboard to extruder for Creality Ender 3 V3 SE, the reason is that it holds the cable close to the base saving some space on the descktop and it holds the cable in place from moving.To attach...

The Creality CR-6 SE print head cable installation is a bad design. The connector on the print head should a least be at 90 degrees allowing for a more natural flex motion in the ribbon cable as the carriage travels left to right. Also it adds...

This is a remix from https://www.thingiverse.com/thing:4657122 I didn't like the way the original design of this hot-end cable guide forced this cable to be twisted. So I redesigned it. There are two versions, one without the PTFE bowden tube...

Holds the cable up a little higher, which can provide easier access to the power switch or allow things on the table next to it. Snaps into place. Depending on your printer setting might need to extend the Y-axis a percent or two.Works on my printer,...

I am not the original creator of this design. that credit goes to sani3d. ...+ ptfe tubing clip 2 in 1

Simple clip to attach the Bowden tube to the braided ribbon cable on the CR6 SE replacing the stock black ones that don't really work. This print should help prevent the ribbon cable being a fatigued. ... Plus it just looks pro

CR6 SE Rear Ribbon Cable Tidy. A simple bracket that clips into the extrusion in the same way as the stock filament holder. Keeps the ribbon cable nice and neat and away from the Spool. Hope it Helps, hit like if you like it! ...

... UPDATE ! Based on this "cable bumper" https://www.thingiverse.com/thing:5149848 I´ve made a cable guide specific for a position >=45°. ... Because without this part the cable can stuck in front of the motor and printer will fail with homecoming..

This is a remix of [*madizmo* one](https://www.thingiverse.com/thing:4562729), but with a lesser angle to avoid bending the cable too much. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/9qBGdb3e4fE <iframe...

Modified the original cable clip (https://www.thingiverse.com/thing:2960375/remixes) so that USB cable fits. ...I use it to fix OctoPrint/Raspberry PI USB-cable so it doesn't snag into any moving parts.

An alternative cable clamp for your Ender 3 V3 SE that includes the signature Ender logo.

Remix of Sidewayz_Control's [Cable support for the Creality CR-6 SE](https://www.thingiverse.com/thing:4654645). Also fits the CR6-SE Max, as reported by [Tchunass](https://www.thingiverse.com/tchunass/designs) in the comments - thanks! The cable...

Remix of Sidewayz_Control's Cable support for the Creality CR-6 SE (https://www.thingiverse.com/thing:4654645). (I can't get the Thingiverse "This is a Remix" option to work right now, no idea why) The cable support itself is remixed to add a clamp...

I liked the first cable chain design very much, so I added just a top link hanger element - small piece attached on a side by two micro screws, that can be hanged on the original cable ribbon clip.

Thanks to MB_AUZ for great concept: https://www.thingiverse.com/thing:4653730 I have just added a bit of height and now the cables are straight up, plus the bowden support is not clip-on but full through-hole. ... Great initial design, though - full...

This is designed to be clipped on to the modified filament sensor case here https://www.thingiverse.com/thing:4635094 and it will direct the cable over the extruder instead of down the side of it. I have not printed/tested this, but it should work...

I don´t have includet this part .let me know if it was packaged for you .

This is a very simple remix. All I did was trim it a bit where it clipped over the metal frame so I could use my own PTFE support with the part-cooling fan bracket that you can see here https://www.thingiverse.com/thing:5406079 - I've discovered that...

You can %98 scale to fit easy, but I tried %100 scale, its OK.

...just a quick hack....'cause I got tired of the thin arm always breaking off. ... ...my X-Limit Switch Cover remix makes an excellent companion ..Thingiverse 4875515 ...also, consider PTFE tube support remix....Thingiverse 4682557

Re-mix of a CR6-SE ribbon cable guide to personalize it up somewhat

Support Ukraine, we will be free!The linear cable clip for Ender 3 V3 SE is a practical accessory designed to enhance cable management in your 3D printer setup, especially in preparation for moving your 3D printer to an enclosure. Specifically...

The cable for the heated bed on my CR-6 SE was catching on a corner of the Z-stepper motor. When the bed moved forward, the cable would get caught on the edge of the motor and scuff. This bumper slides over the Z-stepper motor. It provides a...

... Since adding it, I haven't noticed any more scuffs in my cable.I had to modify the design after I replaced the plastic spacers under my CR-6 SE's bed with silicone mounts, which caused the bed to sit slightly lower and rub against the cable bumper.

Cable holder for Ender 3 v3 SE. Should also fit KE, but havent tested that.I recommend using Cable_holder_v2.stl, there are 2mm tighter/wider versions if you want.Simple adjustment of the original cable holder by Vally544. It was very well designed,...