sdkfz model

Infill doesn't matter because the model is a hollow shape. The filament must be elastic and reasonably heat-resistant. I have tried this in NinjaFlex which seems to work well. Anything much harder than Shore 85A is likely to be too stiff to act as a...

It's also compatible with the Chinese clones of both these models, often referred to as "J-head" extruders. There is a cable guide built into the design which will assist with keeping everything tidy and reduce any stress on the heater and thermistor...

Please feel free to build on what I've produced, maybe tweak things to find a home for the hero boards or a model of the Batmobile. I'm going to keep my Hot Wheels Batmobile with the hero boards in the Arkham Asylum box. ... ## [CLICK HERE TO...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

It was just hard to get some of the screws in it so I had to manually remove the parts this model has removed for you. Make sure is you use screws to hold the bearings tight that the lowest ones have low profile heads or they will be lower than the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_pattern_thickness = .8 custom_back_extra_port_y_size = 30 custom_back_camera_corner_resolution = 8 custom_top_port_x_position = -10...

... 3D model created using SketchUp Make (free software). I also tried 45 degrees, but the fan's thickness made it touch the desk surface below, so it had to be skooted up to the high end of the stand... thus the cooling effect would be diminished.

Supports: Yes (if using Cura we recommend using the Tree supports option and adding a 'Brim' to help the Tree supports adhere to your print bed) Rafts: Doesn't matter Links View on Cults View on Thingiverse License The "Personalised Voronoi Sphere...

... - Schematics:  Goggly eyes are optional, but they improve performance and friendliness of the finished project. Modelled using tinkercad & blender. ...

UPDATE 12/25/19 -- Total remake, This model is now outdated.. New version 2.0 at https://www.thingiverse.com/thing:4066146 Another Update 5/4/2019: I've added another sleeve to hold a bearing for faster spinning gauge. I've also swapped to PETG...

... first using TinkerCAD to get an idea of the geometry needed. Then I used OpenSCAD to create a parameterized model for customizer. Use the image shown to understand what the key parameters control. ...Overview and Background Lesson Plan and Activity

And for many builders I consider this simpler than going the path of printing Flex material.  Model DetailsPulley and Bearing Press ToolThere is not much to say. It shows the pulley with a bearing and heat-shrink tube on the outside. The third...

###Standalone car lift available too: https://www.printables.com/model/243829-hot-wheels-164-scale-car-lifts Description ==================== A generic garage display made to fit 3 cars, the front of the garage mascot is based on Koupen Chan design....

Don't use it for rendering or model generation. (see Reducer picture) PRINTING NOTE Print at 100% infill. Try and print standing vertically, if possible so that scaffolding may be ommitted on the inside. These are for sink and drain plumbing only,...

If there's interest, I can also upload the design files for other models. Please share your creations if you remix. Update: The original inner joiner STL was undersized. I've added a new STL that should be properly sized with everything else in the...

I started with the photos of the metal models (I've uploaded those photos to thing:1618843) and went from there. All the design work was done in Moi (Moment of Inspiration). Once I had an escapement design, I ran it as a simulation (unsuccessfully)...

I have not printed/tested these myself - I will remove this note when I get confirmation that everything fits correctly. lrs-350_foldingCover_front_blank.stl this one is completely blank, you can add whatever cutouts you need for components of your...

As far as assembly is concerned, it's all pretty self-explanatory when you see the models, but here are a few tricks: Use as little wire as possible, but make sure you use good wire. The wires run from the grip and back, across the side of the...

Modeled to look like a pirates spyglass, this kaleidoscope will be so much fun to play with! I printed in primary colors to preserve that playfulness. The pieces should slide together right off the print bed. This was designed so that the Barrel...

If you need to use a different pump you can model and print your own adapter as it is just a rectangle block with a hole for the pump water outlet. The inlet block should be 80mm tall and 32mm wide minus half a millimeter for fit tolerance. If you...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 0 custom_corner_resolution = 8 stencil_drawing =...

Get the entire plow here: https://cults3d.com/en/3d-model/various/scx6-plow I have designed this plow for the SCX6. The blade reaches a size of 15.5 (394mm) wide. This does limit a print to some bed that have a 400mm build value. However, I have...

;-) How did I end up with two of these devices? At first I bought the 2TB version and wanted to replace the HDD with a 5TB model. I tried several things, but nothing worked. With vaccation ahead, I ordered a second device with 3TB. The electronics of...

It started with a Bachmann starter set with a steam loco and a couple of cars (Durango & Silverton in case my other models didn't give it away). This came with a bunch of EZ-track. I had full intention of expanding my layout so I bought more...

Constant testing and printing are underway with mods on nearly every model, wasting over 300 feet of filament in the process. I'd appreciate support for my project as it's not intended for non-3D users but rather for those who want to quickly build a...

Below are my non-printable parts: https://www.amazon.com/Miniature-Bearings-MR63ZZ-L-630-673ZZ/dp/B00ZHSQX42/ref=sr_1_2?ie=UTF8&qid=1476061067&sr=8-2&keywords=6x3x3+ball+bearing...

(This is all also in the README)I commissioned prints for these models using PLA with 40% infill and they work like a charm.- You will need to print the Rear Panel if you want to use the parts in the MOBO and GPU folders.- The PSU folder needs to be...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

Description: https://youtu.be/G9-N-nIqc4g Assembly: https://youtu.be/2hdSGDdjpeQ Torque Capabilities Please note that I designed this CVT for a demonstration model, it's not intended to be used as an actual transmission. How This Works - Watch the...

Don't use it for rendering or model generation. (see Reducer picture)</p> <p>PRINTING NOTE</p> <p>Print at 100% infill. Try and print standing vertically, if possible so that scaffolding may be ommitted on the inside.</p> <p>These are for sink and...