scx24 shock spacers 3d models

A simple set of preload spacers that will fit the stock Shocks on your SCX24 and AX24 rock crawlers. These can be used to adjust the amount preload on your shocks, therefore adjusting ride height of your crawler itself. When used in the new AX24...

Shock absorber with longer displacement for the AXIAL SCX24. Designed for 1.2mm piano wire and original springs. Shaft should be 22mm long and glued to piston and eyelet (thus cannot be disassembled. Make sure to put the pieces together in the...

Scx24 dual shock mount

scx24 rear shock mount outboard

Front shock tower and receiver mount for SCX24 use with telescoping 43mm shocks. this will keep the front driveshaft from binding. can be imported into CAD and add different shock mounting holes if desired. ...1.5mm holes

... rear shock tower is the same left to right. The other ones are labeled for passenger or driver. I also designed these to fit scrambler tires on both vehicles. For the lower shock mount, I just reused the lowers off of the original SCX24 shocks.

I was looking for new upgrades for my scx24 because I wanted more shock mounting positions. As I was scrolling through various websites, I came across something like these, but they were about $10-$15 for a set, so I 3D printed my own.The Axle Shock...

This is a set of upper shock mounts for putting Carisma shocks on an SCX24 deadbolt or C10. I used M1.4x6mm screws to give it a little extra grip vs the factory M1.4x5mm, but the shorter screws would probably work. Carisma shocks bolt straight into...

My design was HEAVILY influenced by the following design (https://www.thingiverse.com/thing:4750007), but I wanted to mount the shock under the frame rail rather than on top. The numbers are dimensions for the shock in comparison to the front...

... it boasts a robust structure achieved through the strategic use of full infill and a detailed layer resolution of .2. Designed for seamless compatibility, it easily integrates onto all 1/10 scale shock absorbers, ensuring a secure and stable fit.

### Printing Notes: 2 x `AxleShockAdapter.stl` 2 x `AxleShockAdapter_mirror.stl` ## BatteryPlatform A replacement battery platform with larger holes for mounting carisma shocks. Many options allow you to adjust shock angle based on your preferences....

Created a rapid-fire design series of shock spacers in numerous diameters - 2mm, 4mm, 6mm, and 8mm.

Shock spring clips and spring preload spacers for Rustler 4x4 VXL or other models with same shock size. Seems to work well. Preload10mm on Front and 13mm on rear. ...

Preload spacers for Dlux Dravtech / Traxxas big bore shocks. I made these to work out the preload i wanted to add. They slide on without removing the shock. I intended to replace them with the rubber O rings supplied with Dravtech shocks once i...

These towers extend the available shock mounting options on the Injora LCG chassis for SCX24's to allow the shocks to lay down a little more.

In theory, the internal spacer will act just like (multiple) DVO bands placed on the positive air side, aiding bottom-out resistance by making the shock more progressive across its travel. ...The following are approximate volumes/relative sizes for the...

Made these to grip tyres better when using extra wide beadlocks on scx24. ...2 per wheel one on inside and one on outside as you can see from picture.

I needed a battery tray that was larger, and that actually fit the stock battery that came with my Scx24-C10 , and that also had the ability for lots of adjustment of the shocks.

This is just a rear shock mount for the SCX24 that keeps the same ride height but lays the shock down to increase articulation. It's designed to work with the bodies that don't use the rear body posts. ...You'll need to mirror the Y axis in your slicer...

Version 2 Update: March 27, 2022 This mounts to the front of the factory frame and provides multiple shock mounting positions as well as body and accessory mounts. It's designed to fit with either the original or Furitek Komodo motor installed. ...

The shock tower boasts multiple mounting points to raise or lower your ride height. The slots on the sides work perfectly with zipties (displayed) or rubber bands to secure your battery. Keep in mind that your battery wires will likely be a tad...

Shock pre-load spacers in 2mm increments 2-12mm.Fits Traxxas ultra shocks 13mm body diameter

... access the required components. ...Four distinct sets of spacers are available, tailored to specific sizes: five millimeters, ten millimeters, fifteen millimeters, and twenty millimeters. ...Select the appropriate size needed and proceed with printing.

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/ffyUWzOq32O

It WILL NOT work with a stock SCX24 battery.The shock mounts may not clear large aftermarket servos, especially on a standard wheelbase SCX24. My test truck runs an Emax ES08MAII on a stretched Deadbolt (144mm).ASSEMBLY: If you're printing in PLA or...

It lowers the CG by making the receiver/esc tray at a 35 degree angle like the frame rails, it also gives more mounting positions for the front shocks. I designed it to mount directly in the stock mounting holes and it works with the stock front body...

Shock preload collars fit snugly around 12-13mm shocks, while internal shock spacers are designed specifically for 3mm shock shafts. ...These spacers come in a variety of thicknesses, including 0.5mm, 1mm, 2mm, 4mm, and 8mm options, allowing users to...

This product features three volume spacers designed specifically for the Fox Float Rear Shock (CTD LV). These authentic parts, unlike 3D printed versions, are made from hard machined plastic. ...Although they have not been tested as 3D prints, their...

The shock mounts and back endstop mount with M1.4 x 4mm or 5mm screws (6, total).There are two back endstop options - one with provisions for magnet mounting and one without. If you use the magnet mount, you will need (4) 10mm x 2mm neodymium magnets...

I removed the body mounting hole as i was not using it and was watching weight. Enjoy. ... The part needs to be mirrored to make a matched pair.