scx24 c10 light bar 3d models

My apartment was just not quite bright enough during the evening so I wanted to make a cool light fixture to go in the corner that would add some lumens in a diffuse way. I of course wanted to 3D print this and make use of the wood bars and LED...

... MK3. The light bar attaches to the back side and provides exceptional illumination on the print bed. ... I also designed it so that I could still support dual Mark3 Spool Holders without any interference: https://www.thingiverse.com/thing:1832235

This is a remixed light bar for www.thingiverse.com/thing:3292889. I added a 45 degree angle so the light points more directly under the extruder, and I add slots to reinforce the LED strip adhesive with small zip ties. Supports: I did not have...

... - it's always there when you need it most. To ensure seamless printing, I made sure to preserve the full height of the Z axis. For better visibility in the second photo, I positioned the light source at the front, providing optimal illumination.

I have 2 versions of the front bar, as one has a mount for the Wyze cam as shown in the photo, and one does not. Please give me some feedback on how you like it. I have below the light I purchased from Amazon that was designed to fit into this. very...

This is still a work in progress but here they are, SCX24 Rock lights. These utilize two sets of the original led from the front bumper with the wires extended. ...I printed these at 100% infill at .18 layer height with no supports but your settings may...

I designed this for my aqurium as there was a mount for a led light on it but I had two play lightbars that I thought I could use instead. It's very niche but thought I'd post it anyway. ...Might make a stronger version as there is some flex

Realy liked the original design, but also wanted lights on the other side of the top bar :-) This have to be printed in a 45 degree angle on the bed to fit the Ender 3 print area. ...Also made a 30 cm LED strip holder for 5050 strips or similar, and had...

The original model is at an angle, which makes it stretch into the print-zone.If the printer reaches that height, the gantry can hit the light bar, and knock it off from it's place, which can lead to damage in the 3D print, or worse, the printer...

It's incredibly sturdy and won't budge even when pushed down hard at the light mounting points. The bracket has a 2mm clearance above the Z-axis brackets to clear the smooth rod and lead screw. A central screw hole allows for easy attachment of...

Phillips hue bar Mount for fish tank. ...5mm gap for aquarium glass

End of light bar is even with end of X axis. Print instructionsAssembly Instructions Buy the Parts Kit Here Necessary tools: Soldering Iron Solder Wire strippers Needle nose pliers Small flat head screwdriver Using the terrible wiring diagram picture...

... side bar with some zip ties. I used a small screw to lock it in place in the middle to the bar. The one in the pics has been run pretty hard so it does not look its best. But its a great print! ... If you have any issues printing post a comment.

...Use the adhesive pads to secure the light bar to the printer frame, and hot glue the switch the the frame. 3. Cut off the usb plug on the end of the led cable, and route the cable through the hole for the z axis limit switch (see pictures). 4. 5.

... long which allows me to put it side by side to obtain the desired length. ... Fixing is done using M5 screws on the rails of the 3d printer. I applied 6000K LED tape to the printed bar and the 15cm size of the bar matches the cut of the LED tape.

I added a switch at the bottom of the right arm (super easy access).To fix the led support, you will need 2 M5x12 screws (Original, it bottom 8mm long, they are little short, you will need 12mm minimum, if it is longer, it is not annoying)I haven't...

If you print it, I advise you in white or transparent Files:Prusa MK3 model: https://www.prusaprinters.org/fr/prints/3267-led-light-bar-prusa-i3-mk2mk3Switch housing:...

This, I reasoned, would put those delicious photons right onto my brain windows. A couple hours of tinkering in CAD later, this is the result: a 3-foot light bar that hovers above my monitor. It turns out the big wide diffuse light also does a good...

A couple hours of tinkering in CAD later, this is the result: a 3-foot light bar that hovers above my monitor. It turns out the big wide diffuse light also does a good job making me look less horrific in my all-too-frequent Zoom meetings! I chose...

Click below for the MK2/MK3 versions.MK2/MK3 Light Bar Files:MINI Light Bar: Standard version of the MINI Light Bar. File comes in the correct orientation for printing, no supports required. Smooth sheet required for tight fitment of front and...

A couple hours of tinkering in CAD later, this is the result: a 3-foot light bar that hovers above my monitor. It turns out the big wide diffuse light also does a good job making me look less horrific in my all-too-frequent Zoom meetings! I chose...

This is a 200mm wide LED light bar designed for the Ender 3, utilizing a 24V LED strip and a 24V toggle switch connected to a 24V power supply. I submitted this without a photo because I was redesigning the mount and haven't installed it yet. Note:...

Remix changes include: Adding snap system on LED arms Extension bar for more LEDs 2020 clips

I've reworked an existing design for an LED bar, giving it a fresh twist by adapting it to accept a M3 x 10mm screw and matching nut for added versatility in assembly.

This is a slightly modified version of this (https://www.thingiverse.com/thing:3376399) LED bar. ...I've modified it to take a M3x10mm screw and nut Category: 3D Printer Parts

......1 is for 10mm wide LED strips and other is for 8mm LED strips.Can be scaled to any size in slicer.End Mount 40's can be mirrored for opposite ends.Use coupler to connect 2 bars.mounts can be mounted to V slot rails using M4 12mm screws and M4 T nuts.

This is a diminutive RC lighting system consisting of a compact LED strip controller.

A transparent light diffuser for 12v (12 inch long) LED lighting. ... https://www.amazon.com/gp/product/B094R1VNQX/ref=ppx_yo_dt_b_asin_title_o09_s01?ie=UTF8&psc=1

I'm getting ready to install a LED lighting system on my Redcat Volcano truck, using a Dollarama work light as the base with an added LED strip for extra brightness. ...Stay tuned for some photos of the project!

Needed something to light up the printer below the hotend. ... Remixed the connectors from https://www.thingiverse.com/thing:3147899