scx10 esc 3d models

This stand is designed to support Axial SCX10 ii models under the chassis, with the possibility of accommodating other models as well. The height of the stand can be adjusted by sliding the supports into position. Two distinct types of supports are...

The flat bed originally designed and printed for our SCX10 iii Gladiator Aussie Style Overland build. The flatbed comes with 2 different versions of an oversized, extra beefy chassis mount, one used for our build, and the other which is slidable...

The flat bed originally designed and printed for our SCX10 iii Gladiator Aussie Style Overland build, which can be found here: https://www.aheadrc.com/gladiator-overland-custom-build The flatbed comes with 2 different versions of an oversized, extra...

This is a tube front bumper similar to the SCX10 Honcho stock one (180mm and 200mm width versions (180 pictured)). Note that this version is slightly different than the picture in the way that it mounts (not clearly visible). It is shown in low...

I've finally completed the Interior that will fit the SCX10.2 RTR, and it's a game-changer. The higher tunnel allows for complete clearance of the transmission, unlike the Kit version with its built-in transfer case. This print is expected to take...

... depending on how you want to install this. The TRX-4 one should work with pretty much anything, because the TRX-4 rails are the same as SCX10 except that the channels are deeper. Use at your own risk. Wrench to drive or drive to wrench? ...

To make it more rat rod-like, I squashed it down 20% and made some adjustments to fit it onto a SCX10 frame. Ossum's work is truly amazing! At this point, I'm not inclined to reinvent the wheel, as his rendition is so impressive that I don't have...

And some other adjustments to fit it on to a SCX10 frame. His work is amazing! Some day I may make my own but I'm not there yet, ant to be honest his rendition is so good, I don't have much drive to re invent the wheel. Parts are laid out in the...

While this design is still in development, I recently acquired an SCX10.2 and decided to adapt my body design to fit it perfectly. As a result, I've left it open for users to customize their own body height according to preference. The design screws...

And some other adjustments to fit it on to a SCX10 frame. His work is amazing! Some day I may make my own but I'm not there yet, ant to be honest his rendition is so good, I don't have much drive to re invent the wheel.</p> <p>Parts are laid out in...

scx10 III Servo winch Mount

Direct bolt-on front bumper for either your SCX10 or SCX10 II.

SIMPLE WHEEL SPACER FOR THE SCX10 III

Rear bumper axial scx10 jeep wrangler.

Mount a TRX4 Trans on an SCX10-2 skid plate

This mount is designed for an scx10 3 gear trans. ...

SCX10 ii front solid axle reinforced. ... Cheked in Ultimaker Cura.

Low profile rear bumper for SCX10.2 XJ

3mm offset bumper mount to suit scx10 and scx10.2 frame can be inverted to suit desired height for fine fitment of bumpers may suit other chassis such as scx10.3 or element enduro

Rear cage pivot mounts specifically designed for the Axial Honcho rear cage are available, suitable for both SCX10 and SCX10.2 models of the vehicle.

This is my innovative design, take it for a spin - it's a winner when paired with an RC4WD Bruiser body attached to an SCX10 chassis, and it'll also perform flawlessly on the upgraded SCX10.2.

Post mount front bumper for Axial SCX10-2/SCX10-3 vehicles. (2) light buckets for 5mm leds, compatable with Axial light bucket lenses (AX80045). ...Uses stock pin hardware for mounting and (1) M2x6 screw for the led retainer.

Rear body for trail honcho on SCX10 V1. ... Fit the cab and the fixation points.

Front Support Assembly Scaled Down For The Rubicon Body Of An Axial Scx10 Vehicle Now Completed.

Rear axle utilizing SCX10.1 knuckles, C-hubs, lockouts, and shafts, paired with 10.2 gearing.

Axial SCX10 Front Steering Link Bar V2 Enhanced for Improved Clearance and Travel.

ESC-70A-

ESC Cover

Hi, this is a case for backfire g2t esc, please feel free to modify it for similiarly sizes escs.

Using the SCX10 axles and gearbox give it reliability and link lengths below give a good driveshaft angle front lowers 127mm front uppers 114mm rear lowers 110mm rear uppers 105mm front driveshaft 135mm rear driveshaft 120mm The only weak part is...