scx10 3 3d models

front and rear body mounts to suit scx10.2 chassis with roll scale ifs kit with hardbody mitsubishi pajero

For more information about the Toyota Hard Rool Bar SCX10 RC 4WD K5 Trx 4 model, visit these links: https://cults3d.com/en/3d-model/various/toyota-hard-rool-bar-scx10-rc4wd-k5-trx4...

This main part needs 3 of the hinge retainers printed. They can be attached with a 1mm pin and then have the retaining hole on the main housing cleaned with a 2.5mm drill bit. Once cleaned, an M3 bottom tap can be used to tap the hole for the 6 mm M3...

Requires approximately 5.8m of filament (you're going to want to print support structure too) and just under 3 hours to print at standard resolution. Strictly for personal and private use, not licensed for commercial use or reproduction or in...

Remix of SCX10.2 shock front hoops by justicedspencer This is the V1.0 of shock hoops for the SCX10 2 that allows for scale angle shocks (straight up and down, not angled) and allows for long shock travel while maintaining a low ride height. The...

Remix of SCX10.2 shock front hoops by justicedspencer This is the V1.0 of shock hoops for the SCX10 2 that allows for scale angle shocks (straight up and down, not angled) and allows for long shock travel while maintaining a low ride height. The...

Create a 3D-printed front bumper for your vehicle to enhance its appearance and protection.

Functional at all times, designed specifically for Jeeps but adaptable to various vehicle platforms.

bon print

nearly identical to the GSpeed one just slightly different edging.

Here's a reinforced chassis system designed specifically for the SCX 10 and 10.2 off-road buggies from Traxxas. This sturdy component enhances stability and provides improved resistance to shocks, making it perfect for rugged terrain and high-speed...

capot + paroi + base = box for all ellectronic including Rx, light control and winch control and whatever you want. required 8x M3x10 screws parois2 and base2 if you need the cut-out for the rear upper link fixation. required 8x M3x10 screws rear...

Fill in area under fuel cell to make it seem more realistic

Spur

Hey hey. After my original transmission case broke in half, rather than buying another, i decided to make one. It uses the stock gears ans stock motor mount plate, but will need different center plate mounting holes due to the design. I made it...

RC Crawler shall

simple rock sliders.

Parts for the Axial SCX10II Deadbolt. Two Grill options, with or without a skull. I used a white paint pen to highlight the lettering and emblems. So Far they fit nicely in place and designed to use a 3mm screw to attach to the body. The inside for...

u can use with zip tie

rear bumper for adding 4 lights with 8mm buckets

A full Axial Deadbolt SCX10II Front Grill that includes a backplate that allows for the use of 5mm leds Print at 100% infill

This upgraded suspension system adds a bump stopper, raising it above stock height while also enhancing the steering column by adding more bolt holes to securely attach a raised support for the battery tray.

Hello, I designed those wheel wells to give my truck a more authentic scale look. They mount directly onto the suspension system, and fit seamlessly with the Falken Edition Jeep body. The front one can be mounted on any truck without issue, but the...

I Raised It by 2cm. ... Print Settings Printer Brand: Zortrax Printer: Zortrax M200 Rafts: Yes Supports: No Resolution: ...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/f8dyxosyTXy

The bolts attach straight to the frame, making it simple to install a panhard bar. ...The M3 screws are used for assembly.

good print

I modified the design and frame to suit my needs, strengthening the sides of the box and making sure it could slide smoothly between the rails. I used an existing hole in the frame as a secure anchor point by screwing it in place. The infill is...