sculpfun s9 laser 3d models

--------------------------------- ITA------------------------------------ Posizionatore per il laser della Sculpfun S9. Io lo uso per posizionare le piastrelle (o qualsiasi cosa che vogliate incidere/tagliare che abbia un angolo retto in basso a...

I recommend to center the laser from the software, then, using two vertical positioners (printed with different colors), manually center the engraver head as shown in the pictures.Also in the picture:Z-Axis lift:...

I recommend to center the laser from the software, then, using two vertical positioners (printed with different colors), manually center the engraver head as shown in the pictures.Also in the picture:Z-Axis lift:...

I updated my s9 mount to allow more adjustment and clearance behind the laser.

Needed a screw down adjustable s9 laser mount for my quick change block on my ender 3

This is my design of mounting feet and height extender for the Sculpfun S9.I'm not sure, but I think it should work with the S6 (Pro) as well.These are mounting feet including the possibility to increase the printer, depending on how high it needs to...

This Air assist is for the Sculpfun s9 laser module. It accepts silicon tube ID4/OD6. Optimized for 0.16mm layers. Will replace over lens cover. The design is the same height as the stock cowl and the focus is applied the same ways as with the stock...

Air assist for double hose with 6mm outer diameter. More air flow if you use a membran pump. ... The Y connector is made for 2x Ø6mm hoses and a Ø10mm outer diameter input hose.

The models from Kinetik were originally too high for my purpose.My version only increases the laser hight only by 3mm. ...The module is therefore lower and can also cut very thin things such as paper in a fixed position</p><p>With the additional...

... file to <i>chamfer.scad</i> for convenience. 08/02/2022 - LATE UPDATE! When I put these on my Sculpfun S9 I found that the top of the knob barely cleared the X-axis driveshaft - I have reduced the height by 1mm to give a little extra clearance.

Design: I modified the OpenSCAD code for my M3 nut screw heads (https://cults3d.com/en/3d-model/tool/m3-screw-knob), enlarging it a bit and adding a cavity for the Sculpfun fixing screws. At the moment they seem to work well - I have yet to prove...

Plus the base for attaching and positioning the grate to the Sculpfun s9 laser feet. You should buy metal flat bars with a size of 3x10mm and any length (50cm for Sculpfun s9). ... The flat bars are mounted in five versions, for the widths of 3mm, 3.1...

Replacement for the laser focus on the sculpfun s9

Couldn't find a 3d model of my Module laser From SCULPFUN. ...So I made it myself

This fits the S9 Laser by Sculpfun. Because it blocks view of the beam for setup, I added pointers for alignment. I use a 5 volt 5015 fan driven from the "Extra" pins and triggered by A3 or A4 pin. I use a mosfet to allow control through the...

Modelo retocado para una medida mas estrecha ya que el original es demasiado grande para el cableado que lleva

Nozzle for setup to laser Sculpfun S9 (S9AU20LS) for compressor connections. ... Metallic tube on photo, you can take from telescopic antenna 3D model created for coPET and PLA placsic and nozzle 0.4mm

After building the laser engraver by infectedfpv26, I found the Sculpfun S9 on Bangood was on offer, so I bit the bullet and purchased it. only thing then , of course the laser mount was incompatible with the S9 so I designed this. Nothing fancy...

After building the laser engraver by infectedfpv26, I found the Sculpfun S9 on Bangood was on offer, so I bit the bullet and purchased it. only thing then , of course the laser mount was incompatible with the S9 so I designed this. Nothing fancy just...

This is my design of mounting feet and height extender for the Sculpfun S9. I'm not sure, but I think it should work with the S6 (Pro) as well. These are mounting feet including the possibility to increase the printer, depending on how high it...

This is my design of mounting feet and height extender for the Sculpfun S9. I'm not sure, but I think it should work with the S6 (Pro) as well. These are mounting feet including the possibility to increase the printer, depending on how high it needs...

This adapter (the height) is designed to work with a 20mm thick honeycomb table. Brim is needed because corners tend to warp, but if you have other solutions against warping, use them! This design takes really a long time to print, if somebody is...

I've been sick about the bulky "okish" solution for the mounting plate of the Sculpfun S10 laser head to my S9.So I've designed my own, lightweight cover. It only weights 13 g after printing my version, so no much weight added to the axis. Changing...

Remixed this air assist nozzle to fit inside the laser shield of the Sculpfun S9/S6, you will have to modify the shield for the air nozzle and glue the nozzle inplace.. I also put some holes around the bottom of the shield for better airflow. ....

The orginal file can be found here: https://www.thingiverse.com/thing:5236996After upgrading my S9 with the S10 laser head and the linear axis upgrade, i needed to adjust the mount for the lift a bit. ...I also added a version for cable and tube...

I decided to make this adapter to add a Sculpfun s9 laser to my S totem.

Based on the original work of MattMacOne for his Neje adapter. ... The original adapter was too small for my LM2, so I enlarged it to fix my LM2 with Sculpfun S9 laser head mounted on it.

This is my version of the air assist nozzle for a sculpfun S9 laser engraver/cutter. Print it with supports only touching the build plate and it should come out ok. I printed mine using a 0.2mm nozzle and PLA+ filament. Its nice and air-tight...

This thing is to add Air Assist to Sculpfun S9 laser engraver cutter. Included is a jig to bend the 4mm aluminum tubing and to cut the end off at the correct angle and a jig to drill the hole through the orange acrylic shield so you don't need to...

Bought myself Sculpfun S9 laser engraver and wanted to have removable hose holder for air assist so I designed it. It is designed for 6mm silicon hose (used for aquariums), if you have any other dimensions of hose I have included Fusion 360 file so...