screw in clamp 3d models

I designed this screw-in auger style drywall anchor for mounting picture frames, hooks, hangers, etc. in drywall. I use these anchors to repair holes that have already pulled out using the smaller non-threaded style anchors. This design prints well...

To assemble the slider, simply print it in place and then use a hex key to loosen the screw that secures it to the tower slot. Once you've slid the slider into position, tighten the screw using the hex key to lock it firmly in place. With the hook...

I broke down the original screw into seven distinct sections and subsequently divided each one along its central axis, thereby providing users with a greater range of printing possibilities for the screw.

Screw-Nut Chess is a clever creation of PARTsolutions. ...For more information, visit http://b2b.partcommunity.com/community/partcloud/index#!part?name=Screw+Nut+Chess&model_id=8781 to explore its unique features and specifications.

 This variation uses threaded parts to allow you to print the upright separately and screw them in. I printed this with a .6mm nozzle, and .15mm layer height.  Note only the threaded sections really benefit from thin layers, so you can...

(I'm not going to make any other sizes, if you want to you can remix it to what you need) If you followed along when building the pool your strainer caps are screwed in place with two set screws. No idea why but they are. Remove the top and bottom...

(I'm not going to make any other sizes, if you want to you can remix it to what you need) If you followed along when building the pool your strainer caps are screwed in place with two set screws. No idea why but they are. Remove the top and bottom...

Got tired of not having a good place to put all of my spray cans so I designed this screw in clip. Put together this video on how they work: https://youtu.be/nJHEA3dAyC4 Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: No Supports: No...

So i made one.https://www.youtube.com/shorts/qi6h9ViouRcThis is a print in place funnel with a screw in design, Its designed on an angle to get around the exhaust on my KLR 650. The thread is m30 1.5mm pitch so it will probably fit some other bikes...

Bread channel adjustments on slicing may require the use adjustment as you cannot print too small otherwise breaking threads is certain during tightening, and if one tightens wrong the threading can easily cross while doing that on bike screw in is...

... sensor. ... Screws into table with 3 small screws. ... Sensor attached with double sided tape no problems Small lip on the rear to attach power supply/power bank Supports optional but prints pretty good without pending you have good cooling.

M20 x 1.5 adapter for mrPens Screw in oil funnel http://www.thingiverse.com/thing:857406 Rather than modify an already great model to fit a friends Bandit 1200 I thought I'd have a go at this adapter. Wasn't too difficult until I tried to maintain...

I didnt like the moss poles that were already on here so I built this one. ...Nothing special to print, no supports and they should screw together pretty easily.

Before you is a side-saddle screw in workbench holder for a glue gun. It's not perfect; the opening could be a bit more molded to the specific gun. But it appears to work okay for my two glue guns and has a hook for your cord (should your glue-gun...

You can use it to clamp the elastic to hold a loop in it making it shorter - it's probably overkill for that as you could also just tie a knot in it, though the clamp would be easier to remove and adjust. However, one of those sleeping bag drawstring...

This design uses a McMaster-Carr 90935A199 panhead screw, but its simplicity makes it possible to use any low-profile screw. ... I have successfully printed this design, which snaps into place just like the original when printed at a layer thickness...

This is a remix of the prusa mini+ tool holder that now uses a screw and t nut for one side. I made this since the original design kept breaking off on one side when I tried to mount it due to the layer lines. ...This print does not require any supports...

Modified version of the DB25 to RJ45 enclosure for the Thanos4U RJ45 variant, which allows securing the DB25 connector to the servo motor driver using two 4/40 UNC x 3/8 countersunk screws. Supports: * Enable build plate support when printing...

... airflow after experiencing overheating issues. ...By fitting these feet into the existing screw holes at the bottom of the laptop, I was able to raise the device slightly when placed on a table, thereby enhancing ventilation and reducing heat buildup.

I opted against securing the camera mount with tape, opting instead for the reliability of screws. To that end, I designed a removable base for the camera mount, ensuring easy installation and removal. ...Additionally, I adjusted the camera clip's...

These were specifically designed to securely screw into place, serving their purpose flawlessly. ...Scissors, pliers, markers, needle files, and other essentials now have designated homes on the cheap bookshelves I've repurposed, granting me effortless...

... items all over the room. To address this issue, I designed a half-cup holder that can be screwed into place. ...Since I don't have a pegboard setup or a dedicated workshop area at present, this solution works perfectly for my current situation.

Crafted and Produced using Solidworks in 2016

This is an easy release clamp/detach device for removing CPUs from the socket using the Delid Tool, compatible with Intel CPU sockets 771, 775, 1150, 1155, 1156, and 1151.

A look at my initial work in Creo Assembly Or, alternatively: Experience with my debut Creo Assembly project Another option could be: Introducing my inaugural Creo Assembly endeavor Lastly, it could also be written as: My first foray into Creo...

In the end, i redrew it since its quite a simple and elegant design. ...I made the walls slightly thicker to accomodate M3 nut and smoothed out the surface to allow for sanding. printed in colorfabb copper filament for its antimicrobial properties

... system. ...Check out the details here: 3d-print-modular-mounting-system-34864. The thread is a standard trapezoidal (power) screw per DIN103, measuring TR12 x 3. ...I crafted this specific bolt to be 55mm in length with a 3mm radius at its root.

Print in place storage box nearly translucent (0.8mm walls). Glue two pieces together to form final lid box. ... Latch locks very lightly due to wall thickness only 0.8mm.

Fix most of warnings and some minor bugsMake default caps a little more thick.Make design more standardSee all instructions in the original work:https://www.thingiverse.com/thing:414556

It consists of two primary components: the Nut, which represents the technical aspects of the project, and the Bolt, which symbolizes the human factor or people involved in its execution. ...By focusing on both elements, this approach aims to guarantee...