scorpio model

I just have to choose a bulb of the wattage I want and with a high CRI to get the best image quality.Since Fresnel spotlights are a classic in the world of cinema, I based my project on a model of the Arri brand from the 1940s. Which has a spindle as...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

# Introduction This is a remix of the Ender 3 HallON v3 Installation kit to fit a Micro Swiss Direct Drive set-up (recent models with additional screw holes on the left. Because I noticed that the hold of the sensor in the adapter gets loose after...

This is a servo hinge setup for use with MIPRESIDENT's Iron Man Mark III helmet (http://www.thingiverse.com/thing:260152). You can see my final build here: http://www.thingiverse.com/make:286759 And a video of it in use here:...

Please check the images to see what it is included in this kit.This set contains: - Northmen Berserkers (12)- Berserker Skinchangers (4 + 4)- Skadi Ulfhedinn – Demigoddess of the Hunt- Gauldurbjorn – Skadi Companion- Wodan the Allseer- Eldormr - the...

Particularly VERY IMPORTANT you need to change the setting from the default Negative Image to Positive Image. Adjust the Model Settings as I have shown in this Thing images. The Size (width) MUST be 150mm. Also I suggest reducing the thinnest layer...

The solution is simple enough: Both parts of the model need to be placed away from the centre point (still properly lined up with one another, obviously), so that the probe can do its thing without the first print getting in the way. So began attempt...

Using a allen key also has a couple of smaller advantages, those being reducing the number of pieces in the model, while also providing the added benefit of acting as a keychain mount.The gadget is made up of a few common parts apart from the printed...

[Video](https://gitlab.com/jdobry/hevo-mgn/-/blob/v3/DOC/video.md) ============ [](http://www.youtube.com/watch?v=EZKwii39ZXY "Video Title") [![IMAGE ALT...

... all STEP files are added for whoever wants to remix/adjust to there liking. Since I always tend to get frustrated by only having STL files of models that I want to improve/adjust I want to save you the pain of this and enable you to be creative :-).

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 74 printer_tolerance = 0.4...

2x 3D printed pulley wheels 2x (or 4x) 3D printed conduit couplers (depending on how you are doing the conduit) 2x 3D printed wing push brackets (based on your plane model) (For any non-symmetrical push brackets, you'll need to print a mirror...

For the launcher and the “motor” (= nozzle and adapter) you can find additional info here: https://www.printables.com/model/46571-water-rocket-and-launcher-platform-complete-instru These parts have been proven to be working (see old video). The...

If you would like to view and interact with the model, you can click here. (You can hide parts by clicking and pressing ‘y’ on your keyboard)</p><p><strong>About</strong></p><p>This clock was created for the Timekeepers contest and utilizes the...

&nbsp;READ BEFORE PRINTING!This is a non-commercial print, this means you are not allowed to sell files or prints of this model.______________________________________________________________________________________What is this?This is my fifth...

It has been argued that for the N2+ model with a print that could fill the entire 2 foot tall bed, these springs would compress and the object would then miss layers and ruin the print. If I were worried about printing that tall with that high a...

... self sustaining for long periods. All ground piping, cabling and the Large Gas collection cansiters would be covered in Dirt once operational for Sun / wind shielding. Note the Space Suit man was inserted for size, got it from the NASA models site

---------- # STP FILES Again I included the STP files, so that everybody with a decent 3D CAD can load the volume models. ### The thread test STP In this file you find a test screw (with the nominal threads) which is identical to the spindle...

Parts Required to Complete:SmallRig Mini V Mount Battery Plate with Belt Clip 2990V Mount Accessory Plate (3D printed or from SmallRig MD2801)M3 x 6 Flat Head Screws (3)Battery StrapVelcro, Servo Tape, or Non-Slip PadWhy I Made This:I recently...

... top layers and tops. but the latest models are off course the best. Please share your towers so I can see how colorful and tall you can make them. ... And don't forget to check out my Instagram: fredslund3d Good Luck & Happy Printing!

I'm no design expert, and 3D modelling makes my brain hurt. However, with a lot of perseverance, a set of calipers, hundreds of edits and redesigns, dozens of test prints, I have made a replacement ring battery.</p><p>You will need the...

This is a Core XY conversion kit for the Ender 5 with Linear rails There is a MK2 version here:https://www.thingiverse.com/thing:4777606 Big shout out to Scott3D for his fabulous work on the Hypercube Evo which I have taken the belt tensioner detail...

Also, no screws or other fixing methods are used. How it works can be seen in the video UPD I added a version in two sides in the form of frames, its printing a third faster and when printing a model, corners closed by cooling by a fan are not...

These parts were designed using advanced 3D modeling techniques, and are not intended to be changed by introductory students. We designed the VeggieMake pins using Tinkercad. We chose to use Tinkercad because we feel it is the best platform for ...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 custom_bottom_fillet_resolution = 8 stencil_horizontal_position = 50...

I have re-modeled them a bit and now there are only a few strings. None if you print them with a 0.12 layer height. Filament Dry Box Set (Updated 3/11/2021) This set of prints are designed for use with the following items to create a very slim...

All the slicers I tried will still slice the model correctly.&nbsp;Parts I used:roller switch:https://www.banggood.com/5Pcs-AC-125V-1A-Mini-SPDT-Micro-Switch-Long-Hinge-Roller-p-998613.htmlslide...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

You may also be able to gently fit the parts into each other and twist to get a sense for how smoothly the connectors fit. Place in a sealable/zip-top plastic bag. Print and fill out a form to help the hospital and make certain that you, as a maker...

The pictures and model views all show the right hand frame. Most of the parts print without supports except for the inside half of the spool, handle post and reel frame that require “supports on build plate only”. I also use 100% infill for all...