scope camera mount 3d models

This is a scope mount for the S&T K98 or any other K98 with this type of side mount. The original mount is quiet expensive and you cant use the scope you want. To screw the picatinny rail on top, 2 m4x12 countersunk screw and screw nuts are needed....

V2 of my 30mm Scope Mount Uses common M4 and M3 screws. Objective is ~1.4 inches high for a medium height mount. No MOA accounted for in the base. Photos are from PRE-sanding and painting. If you print it, please post photos! ...If you enjoy this...

Classic Weaver M16A1/A2 Carry Handle Scope Mount. Measured off originals made by MGW.Updates 6/4/2023:- Changed thumb screw model to feature MGW-style knurling.- Added two additional #10-32 Threaded Holes on the rail mount for accommodating the...

... model: https://www.thingiverse.com/thing:4860572. ... I found the original model too short for me, I wasn't able to set scope properly to my size so I made a rail longer and I added gap for inserting a mount. ...I removed some parts for better look.

I'm creating a custom mount for a shoe adapter of a finder bracket, which will accommodate a mini guide scope for a 200mm lens made by Takumar, with a 60mm diameter. ... The thread I'm using is the same one found at...

These models (scope mount base) are designed for installation on a WE airsoft pistol 1911A1 only. Compatibility with other manufacturers has not been tested. ... For assembly instructions, please refer to the following YouTube videos:...

Move your camera until the dot is centered on the screen; this will roughly point the camera at the sun. The extended separator between the finder and hotshoe provides extra support for longer diameter lenses and solar filters. For optimal results,...

There are some other nice options on Thingiverse, and SNESCUBE64's Super Scope Wall Mount Bracket particularly caught my attention. Upon further thought, though, it wasn't 100% what I had in mind. I wanted a way to hang up the Super Scope with just...

Experimental NATO/Picatinny Mount for Spotting Scope. Unvalidated, untested, untried. Print instructionsCategory: Sport & Outdoors Summary Experimental NATO/Picatinny Mount for Spotting Scope. Unvalidated, untested, untried. Development Comments...

These models (scope mount base) are intended for installation only on an airsoft pistol 1911A1 from the company WE. Compatibility with other manufacturers has not been tested. Данные модели (крепления для прицела) предназначены для установки только...

It's designed to fit an iPhone 8 and a Bariska spotting scope, with the eyepiece diameter roughly measuring 1.525 inches. I made the inner sleeve diameter 1.55 inches to allow for some extra room. The final print was a bit tight on both the scope...

Print Settings Printer Brand: Prusa Printer: i3 MK4 Rafts: Doesn't Matter Supports: Yes Resolution: 0,2 Infill: 100 % Filament: Overture PLA Black Notes: Please print the "Mount" and the "Klemme_1" & "Klemme_2" upright to increase the strength. This...

Just make sure to print at a reasonable infill, as the first thing that would likely break are the arms that hold the super scope in place. A note to keep in mind is that you don't have to use the holes I provided for screws. ...Instead, I used...

Guide scope mount adjustable in two axes.Universal type for VIxen standard dovetail rails on upper and lover sideM6 different lengths screws with self-tightening nuts for drive wheels mechanism.NOTE: For vertical movement screw a specific cylindrical...

This is a versatile Weaver Rail mount perfect for most rifle scopes. Designed specifically for airsoft, this part can also work seamlessly with any other type of weapon. Important note: This part does not drop directly over the rail; instead, it...

Human: V2 of My 30mm Scope Mount Uses Standard M4 and M3 Screws. The Objective Height Is Approximately 1.4 Inches for a Medium-Height Mount. No MOA Compensation Has Been Accounted For in the Base Design. Photos Are From Before Sanding and...

This one-of-a-kind scope mount is specifically designed for the Russian Sks rifle chambered in 7.62 x 39 ammunition. It's a budget-friendly alternative to store-bought mounts that replaces the original rat tail cover behind the bolt, utilizing the...

... it. I haven't yet figured out how to separate them in the model. You'll require four bottom pieces and two top pieces for mounting a scope. ... I can't recall the size of screw or nut I designed this around, but it was certainly not metric.

Scope mount designed for Brass Eagle Nightmare, inspired by classic Brass Eagle advertising visuals. This model is tailored to fit a Brass-bodied Nightmare, potentially not fitting perfectly on an Aluminum bodied Nightmare.\nPrint two units...

I'm excited to introduce my GoPro mount that fits snugly around a 26mm scope, secured by sturdy 5mm bolts and nuts for effortless mounting. The design is an upgraded version of the original part, crafted by farfignewt, who wisely eliminated a...

For fun, and as a bit of a joke, I decided to make a scope mount for a cheap (like £20) airsoft pistol I bought many years ago. I then put a cheap (~£11) red dot sight on top of it I bought from AliExpress **You will need:** - 5 M3x10 screws ...

It is a very snug fit, so you may want to heat up the adapter with a blow dryer before attaching the guide scope. You can also print it a +1% and use a 7 mm hex nut and screw to fasten your guide scope. ... I used a 30% infill at standard quality on...

Remington 511 weaver mount

This is my Lego compatible Scope Ring. Please print out the Test block first, and try it out with real Lego Blocks to test for fit, The side with the notch is A.You will need: 4x M2 Nuts2x M2*12 bolts

Thinner Design Simplifies Wall Mount for Rigol DS1054Z Oscilloscope, Reduces Material Usage and Print Time.

https://www.youtube.com/c/JoeyDoesTech I have also included a new version that allows the mounting of the actual microscope mount that comes with the microscope, so all you need to do is unscrew it from the base and mount it to the plate if you wish...

Optical Mounting base for BHP mkiii. This one is meant to be used with an Aimpoint 2000 featuring low profile weaver rings. ...

Tripod Mount for Celestron First and Similar Telescopes - Enables Tabletop Use Without a Tripod. Requires One 3/8-16 Tee-Nut, Four Screws of 34-38mm Length. Gorilla Clear Non-Foaming Glue Needed to Secure Tee-Nut in Base. ... Suitable for 3/8-16...

Also, you'll need three 3x20mm Allan bolts or whatever type you prefer, as long as they're no longer than 20mm - otherwise, the hinge will hit the flip mount and won't work properly. You'll find the holes for the lower mount for the three Allan...

I imagine if you have a 48mm tube to mount stuff on with a picatinny rail, this would do the job. Requires an M5x12mm bolt and M5 nut. I made this just as a 5 minute joke. I bought a Nanssigy brand one, model JX-703. ...This one:...