sci fi railings 3d models

It´s perfect for ambient light or sleep light in child's room ------------------- HOW TO SETUP ------------------------------ For setup please follow the instructions on the original project page: https://www.thingiverse.com/thing:3354082 You should...

 This requires a relay controlled by the OctoPrint computer that acts a switch on the hot wire between the power supply and the printer motherboard.This model is used to hold a relay on a 4040 rail, using t-nuts and M3 bolts.  Two different covers...

Roads, rail networks, landforms, bodies of water, and structures are all recreated using authentic world data. The buildings, precisely placed to mirror real-world structures up to a certain extent, showcase accurate replication. Please note that...

The two halves of the bracket have rail cutouts leading from the rod hole to the outside, so that the two half can be slid from two sides around the threaded rods to form a complete and strong motor bracket. In order to make sure that the motor...

- 256mm long Weaver Rail from Ali-Express - 1/2" diameter stainless tubing, 1/16" wall, 11.7" long - 6x 1/8" diameter, 1/2" long dowel pins - 6x 1/4-20 x .88 SHCS-ZN bolt - 6x 1/4-20 Nut-ZN -1x 8-32x.75 SHCS -1x 8-32 Nut - 6x 1/4" diameter, 1-1/8"...

I also designed a new console mount sine the old one wants to hang off the top of the rail and it let plastic get into the cracks. For those who dont have a bigger printer just print LHS/RHS instead of the full thing. The bed is no longer hard...

The rear frame rails are the same right and left, so just mirror the left side provided in your slicer software to get the right side. Some designs for 3d printed parts Appreciation to jan1cato, I used his crossbeam from here:...

The modules are connected to four rails, supplying both gaseous ammonia and reform gas to the purifier. Reactor Type: Micro-channel stainless steel Catalyst: 7% wt Ru 10% wt Cs promoted on CeO2 Ru Catalyst required per Kg hour H2 reformed: 0.001 kg...

(photo of it fitted above with the brushless motor) I used the existing 'cam follower' part but snipped off the bottom nug and filed it down to fit in the 4mm square hole on the motor bottom part. Plan is to use the standard 30A ESC from the 12V rail...

This is the tallest building inside The Loop proper, defined by the CTA elevated rail loop. (Credit; Chicago Architecture) This object is part of "Scan The World". Scan the World is a non-profit initiative introduced by MyMiniFactory, through which...

My design uses 3D-printed glass clamps similar to those used in modern railings to hold glass panels in place. These clamps are designed specifically for this project, so you can be sure they'll work perfectly. I also came up with my own safety...

The data pin on the board I used was GPIO 16, then you will want to take the 5v rail and Ground up to both rings. In WLED set them up as individual segments LED 0-24 and 24-48 and reverse the direction on one of them. ...The rest is up to you, get...

X 14.2mm FL precision coated BCX lens ($6 plus shipping) * Red (650nm) Laser Diode ($1-3 depending) Possible cheap XYZ stages: * Manual 3d printed based on http://www.thingiverse.com/thing:144838 * DVD player DC 5v linear slider Mini Stepping Motor...

You can use the ground and 3V3 rail on the RPi to power it, but you'll need to have an appropriate resistor installed inline.It's running the following software: Raspberry Pi OS, with Desktop (it's slow on the Pi Zero W, but it was extremely helpful...

 This one is more compact, keeping the nozzle closer the linear rail glide block and lowers the part cooling fan and BLTouch to the right level for the Volcano.    All models can be printed without supports.If you have an enclosure, I recommend you...

Also shortened one of the rails on the base to match the other/prevent catching on the end. The 6- and 4-card base and covers are interchangeable - but you'll have to make sure you have the correct lever (original lever with original base, and 4-card...

This is so that the bow string has less friction on the bolt guide rail.Effectively, this should reduce wear on the string as well as increase the effective force (due to reduced friction loss). Printing InstructionsMaterial: TPU - needs to be...

The body and door can be printed with any resolution, but a higher resolution (0.28mm) is suggested for the spool holder and its support in the back, as well as the thicker section of the base that bolts onto the rail. For these sections, it's...

using mgn12 linear rails, there is minimum to no play on the axes. i have done my best, also, to keep the weight of the laser head the most centered and close to the x aluminium profile. Belt path is optimized and aligned with the frame. My config.h...

However, for the cleanest install cut the connectors off and solder the + & - fan wires directly to the boost converter. The slot covers are not entirely necessary, but will help keep the mounting point from moving within the rails. If you choose...

When printing this design, the only thing you really should pay attention to is that the top of the rails is printed as close to 4.10 mm as possible. If it's much thicker, you'll have a hard time getting disks in or out of the slots, and if it's...

You can either strap it on the left end of the rails with a small zip tie or glue a small magnet to the mount and it will stick by itself. If you want to use the z-axis mount on the right side instead, make a mirror of it in your slicer. There are...

There are now two versions - the 2040 has a bracket built on the left side to attach this to a 2040 rail (about 2mm up off the floor), and the "stand" version that does not have this support or it's corresponding holes. I also built a quick slide-in...

There are rails on both the swing arm and the upper lift arm for securing the camera cable with velcro straps or wire ties to help keep the cabling under control. This is my first upload to Thingiverse, so I'd love it if you'd make one of these...

When this building was built, the freight railroad tracks that delivered newspaper rolls to the old Chicago Sun-Times building were preserved so the city might some day make a passenger rail link between Michigan Avenue and Union Station and the...

The injection system is a conventional common rail setup. The engine block is fabricated from high-temperature 351 Aluminum Alloy. This innovation allows for increased volumetric power density, and most importantly, a gravimetric power density...

I've included an eccentric nut for printing, which inserts into these larger holes to snug the wheels to the X rail. You'll need two longer-than-stock M5 bolts (30mm) for this. 3) The Commode parts cooler fits on the front and comes in two flavors:...

________________________ If you like my work please consider supporting me on Patreon. Become a Patron! ________________________ Some of my other designs: https://www.thingiverse.com/thing:4165457 - Smoke Stack Addon for Sector Mechanicus...

Barrel: Print either the part labeled rail or cover and epoxy into the top slot in the barrel taking care not to obscure the sight picture. A good seal around this part is required to launch larger projectiles or else it can blow gas out around this...

The software also includes a comprehensive library of objects, including cabinets, countertops, sinks, faucets, toilets, showers, bathtubs, mirrors, lighting fixtures, windows, doors, floors, walls, ceilings, roofs, stairs, railings, handrails, and...