sci fi environment 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

# Introduction This is a remix of the Ender 3 HallON v3 Installation kit to fit a Micro Swiss Direct Drive set-up (recent models with additional screw holes on the left. Because I noticed that the hold of the sensor in the adapter gets loose after...

UPDATE 09.08.2022 •changed length for diffusor and mount from 10mm to 100mm •orientation changed for some models •added end cap UPDATE 12.08.2022 •added with diffusor / without diffusor comparison photo and electronics box wiring photo •added...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

A custom-made enclosure specifically designed for the Raspberry Pi computer assistant Assistant assistant A bespoke casing tailored to fit the Raspberry Pi device. assistant Created especially for the Raspberry Pi, this is a one-of-a-kind case. ...

No support is needed and would be very hard to remove because the support would be inside the model where the magnet eventually slides into. We are depending on bridging for the parts that would normally need support. I have given extra tolerance...

I have re-modeled them a bit and now there are only a few strings. None if you print them with a 0.12 layer height. Filament Dry Box Set (Updated 3/11/2021) This set of prints are designed for use with the following items to create a very slim...

Just copy your gcode to the same folder as the exe, run it, select the options you want and when you've confirmed your choice it will automatically open the first gcode in the same folder and write the temperature changes for you.Extract...

Deck furniture is always a good way to add interest to a model. You might want to install a waterproof switch somewhere on the exterior to save having to unscrew the whole deck every time to turn it off and on. Enjoy sailing your Pocket Boat,...

To connect this to the second hand holder disc, I bought a plastic tube of 1mm inner diameter from a modeling shop. I pinched one side a bit to make it flatter. This seems to work, but maybe I will have to glue it on the pin. I didn't do so yet...

They should easily fit even on small printers; if you can print Hadley, you can print this mount.The mount uses a vinyl disk that sits on top of teflon pads, for very smooth motion.It is very lightweight, and can easily disassembled for compact...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 1 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

The straps used to complete the clamp are downloadable from the original model's site https://www.prusaprinters.org/prints/122320-one-for-all-cable-strap-print-in-place-clamp How to create your clamp & accessoriesSelect the clamp size...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 74 printer_tolerance = 0.4...

Update 220811:Added solid with 1deg step on requestReplace the code below to this, (BB and CC changed to 2 and 1 and replace STL to the new...

The design is made for an E12 bulb socket, but the "Bulb Holder Mount.stl" part could be easily modified in modeling software or simply by drilling new holes to line up with a bulb socket of your choosing. I am considering using an E12 smart bulb to...

The automatic transmission in some models has a tendency to fail prematurely. This usually happens around an average mileage of 108,000. **1.1 Identifying Transmission Issues** Transmission failure can be determined through comprehensive...

If you need a shorter version then I have one of those too, see the shorter Z axis pointer thing.Print SettingsPrinter Brand:CrealityPrinter: Ender 3Supports:NoResolution: .2Infill:20%Filament:Amz PETG/PLAWhite Notes: Printing the...

Theoretically, it can run more than 11 hours on 1 load (not tested). What parts do you need?Plastic parts:You can use the print files if you have an MK3S or you can use the model files and set everything up yourself. The photos show the position...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 6 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 custom_case_wall_thickness = 1.6...

... The single-blade model can be reversed in most slicer programs to cut from one side or the other of the 120 film, as described earlier, in "Preparing This Tool." The OpenSCAD source file therefore lacks any provision to make this adjustment. ...

I was unaware that the MMU2S required changes to the extruder and almost decided to hold off and just install the SPA by itself, but I started poking through the assembly manual for the MMU2S and realized there were changes that needed to be made to...

You have to look very carefully at the top side to see that it is 3D printed. That said, I think I prefer the look of the first version. It is more special with the black part laying on top of the white background.</li></ol><p>Note that the .stl...

If you want detailed instructions with pictures, please see my instructable on http://www.instructables.com/id/The-Bicycle-Bubble-Machine/ Apart from printed parts, you will need: a piece of wood to mount the machine on, which will then be put onto...

 I only buy something off the shelf if I can't make it myself! All parts except the acrylic, rubber grommet, and fasteners are 3D printed.IMPORTANT NOTES:This will only work with the USB port relocated to the front LCD display - or using the new...

No short circuits between the V G and/or S wires. Hardware I used these end-stops: https://aliexpress.com/item/32959048821.html I am not affiliated with AliExpress nor TwoTrees and there are LOADS of identical/rebranded switches out there. You will...

Cómo configurar los parámetros para personalizar la impresión del prolongador para asa de maleta 2.1. Para poder personalizar el prolongador para asa de maleta deberá tener instalada en su ordenador la aplicación para diseño 3D OpenSCAD. Se trata de...

This write up is very comprehensive and written for someone who is not very experienced with 3D-printing/additive manufacturing. For those who are seasoned veterans, I apologize for the lengthiness of the write up. You can just download and...

A challenging learning toy … but perhaps also a clock for the one or other adult 3D printing fan.I got the inspiration for this project from a contribution on Thingiverse (https://www.thingiverse.com/thing:2852026). I completely redesigned the case...