school building 3d model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_left_port_length = 50 custom_top_port_corner_radius = 5 pattern_element_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

These are modelled from the original Type-R parts. (I reinforced these as much as possible). What you need? - Complete RB6 rear mount transmission and motor mount. (Transmission case that comes with the spare part set numbered UM508C.) - About...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

By the way, even though adding a vertical ring might seem counterintuitive, it does provide added stability while still maintaining the original model's benefits: no need for supports, and you can print directly without worrying about brim or...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 4 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 stencil_pattern_line_thickness = 30...

Larger or smaller screws can be used if you scale the model accordingly e.g. M3x8 screws at 150% part scale. Note: it's cheaper per screw if you buy in bulk from a specialist supplier. There are two versions of the container available, the standard...

is ASVFSVF14K203 [US] [CA].----------------PrintingThe “ALL.stl” file prints the entire set of models you'd need to assemble ONE power plug housing. Separate STL file for each of the part is also provided for your...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

Here is a 1:1 scale model of the first rover called Sojourner =) The frame is assembled from a 20x20 mm structural aluminum profile. All parts are printed with PLA plastic, everything fits on a standard 200x200 mm table, but it is advisable to use...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

... glue works for you on PETG. I have made extremely good experiences with YUKI MODEL superglue, which gives me basically unbreakable connections between PETG parts. The mounting plate and the counter plate are very simple to print on their flat sides.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

...More importantly, Thingiverse hasn't run their customizer queue since Jul 10, 2020 so until they fix that issue, you will have to install and run OpenSCAD (free software) on your own computer to process the code to create your own customized models.

(The toothbrush still shouldn't fall out, but a hole any larger and it might...)(I also use a print of the original model as a holder for fine detail paintbrushes, so a hole in the bottom of that one would be rather pointless.)Enjoy!Print...

One uses a buck converter that is very difficult to find at the moment, so this model is not uploaded. This is the one I use. The other one has a larger area inside so you can fit other converters, should you want to. You can ignore the converter and...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_overlap = 0 custom_top_port_x_position = -10 custom_bottom_outer_edge_chamfer_radius = .6...

In order to make it much easier to assemble the case with the RPi4, a few changes were made:Divided the lower part in two halves for easier inserting ofRaspberry Pi;Added snap fit link between upper case and lower case;Using four M2.5x4 screws is...

You just have to have the right case respectively.If you use the original MK3S+ frame check out the version for the original Prusa frame. FeaturesWorks with Raspberry Pi 3 and 4Works with any type of Armor-style case that uses M2.5 screws. Just...

Refer to the pin diagram below.Connect the SMPS OUT- to a ground pin on the RPi.If you're using the fan, install it on the lid.Connect the fan's power and ground wires to pins on the RPi. My 5v fan was a little on the loud side so I used 3.3v and...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

I've designed some custom shelves for my Warhammer 40K model painting supplies, including paints from various manufacturers. The system allows you to mount two shelves on either side of a wall and connect them with chains. For instance, you can...

Note: these videos are uploading slowly, so they might not be fully processed when I publish this model. They should be available in a few minutes.</p><figure class="media"><oembed...

useful as an object holder (Elettronics component, Dyn, various tools, modellism, cutting and sewing, make-up set, manicure, fishing ... etc https://youtu.be/w3FsHNZxC64 Description The chest of drawers is made up of five containers with single...

... If this is the case, and accuracy is important, you should scale up the dimensions a little bit to compensate. I only tested this for small gaskets. If the model proves unpractical for larger gaskets, contact me and I'll see how I can improve it.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 0...

In many channels for the promotion of new electric bikes, people who access the channels, like me, are also excited about the new models of electric bikes, almost always great projects. However, many were frustrated because they would like to have...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 custom_bottom_fillet_resolution = 8 stencil_horizontal_position = 50...

This + rotating the model upside down let's me print the whole thing with no support at all - my print time was 2h 39m and I used small, low-density raft, just in case. https://www.thingiverse.com/thing:4565091 Another thing - it appears that the...