scale model

I also knew that the bluerobotics thrusters were the least cost, most effective option out there for propulsion, so I designed integrated mounts for them as well. I modeled the entire ROV in Autodesk Inventor, then started printing parts out on my...

The propeller in this design is pitched 200% of the blade length, which works much better. Version history Version 1 (1 April 2022)Version 2 (28 April 2022):Updated to correct gap between build plate and drive gear in clearance-check model,...

It was the perfect model to start with as it was multi-part, required many "sketches" to build and extrude, and it required many different skills to complete. I reference sides in this posting, please refer to the "orientation" image (2nd image) to...

The objective is to not create bulky pieces of plastic that distract from the model with the exception of when it is necessary to do so, such as a lift system and a track splitter/track combiner, motor and battery mounts, etc. I will be adding a...

I have not tested them personally so if you need assistance, speak to the mod/remix designer. E3D V6 Bowden Mount If you want to use an e3d v6 bowden setup with STEVE, this mod will allow you to attach directly to the stepper motor mount with...

I designed this model for my daughter, who wanted a treasure chest to go with her pirate costume.  She wanted it to be “really big”, so this design utilizes the nearly the full volume of the MK3s to make three sections that bolt together. The...

And you can create two STL files for dual extrusion. Just downlod the SCAD file from the original nameplate:Then install OpenSCAD on your own computer and follow the customizing instructions on this page.Big thanks go out to RLazure for the...

BETAFPV LiteRadio3 Controller - ELRS Model On the one hand you don't want to skimp, it's your means of controlling your drone. On the other hand traditional radios are bulky, heavy, and seem to be overkill for me. Got a drone with an ELRS radio? Get...

You can now assemble the case in the following order: 1) Insert 2x M3x20mm bolts/screws into the mounting holes of the DHT22/DHT11 PCB2) Thread the stand-offs onto the M3x20mm bolts/screws3) Insert the ends of the M3x20mm bolts/screws into the rear...

Info on this cooling system can be found here: https://www.prusaprinters.org/prints/62523-delta-p-fan-duct-v2-r2-for-mk3s-extruder To accommodate the widening of the X Gantry, firmware changes are required to reclaim the full 250mm printing width....

 The only one brand (pril* ) of my old filament roll is too thick/tall/high to fit,  and that brand stopped selling in my country, so who cares.thickest filament roll to fit is 68mm. How does it lookPlease take a look at the pictures how my samla...

9) Wire the power and sensor wires to the Adafruit Proto-Screwshield (Wingshield) using the 'Wiring' section (above) as a reference 10) Connect 5V power to the 2.1mm jack to be sure everything works as expected 11) Attach the front to the rear of...

Neither here nor on the Internet did I find anything suitable for myself and decided to model it myself. In addition, on the left carriage of the X-axis, Aquila has a technological hole for an incomprehensible purpose. And as part of the spare screws...

The files we sent to you have these already modelled into my own original design bed support arms to fit a Rat Rig V-Core-3 Please note only the VenterMech consisting of the receptacle, unique bearing system and lead screw star drive are covered by...

For the Dual Module the WAGOs are also an easy, soldering free option to combine the cables from both fans.________________________________________________________________________________________________________________ AIMReduction of volatile...

This might seem obvious, but it may not be; the led's needed to be mounted securely, and the front was too thin at that point. added: (same as for the LEDs) more plastic for the display to mount in. changed: re-created the screw holes for the...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 347-480V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.Wiring & Plug: This explosion...

And you can create two STL files for dual extrusion. Just downlod the SCAD file from the original nameplate:Then install OpenSCAD on your own computer and follow the customizing instructions on this page.Big thanks go out to RLazure for the...

We don't use the shell.PrintingPrint all models in their original orientations.The faceplate should face down and needs no support. You might want to add a little bit of negative Z offset to this one for a squished first layer on a rough bed for a...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 347-480V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.Wiring & Plug: This explosion...

Had to drill this out a little to get them to fit.M3x8 hex socket head cap screw• 2 for the Tourbillon-balancewheel to add weightSome sources I’ve used10pcs 2x5x2.5mm MR52-ZZ Precision Ball Bearings Chrome Steel, Metal...

...More importantly, Thingiverse hasn't run their customizer queue since Jul 10, 2020 so until they fix that issue, you will have to install and run OpenSCAD (free software) on your own computer to process the code to create your own customized models.

The fuse holder that the panel cutout is designed for is marked "JEF" inside the fuse cover, and I believe this is that model.2A blade fuse (or source a single fuse locally): From banggood20mm diameter circular snap-fit panel-mounted power...

You have to print the same way by putting the model on its side. <hr /> <p>&nbsp;</p> <h3>My some other things:</h3> <p><a title="Tabletop organizer" href="https://www.thingiverse.com/thing:5274887" target="_blank"><img...

This pencil stand is compact and won't take up much space on your desktop.  This model can be printed in one color. But it will be much more beautiful if you change the colors of the threads during printing. Your imagination will help you. Also, an...

The previous model I partly cut out on the laser, while the Creality K1 with its 600 mm/s printing speed allows me to not only create but also print all the parts (well, you could print the previous one, but it's too much for my nervous system). This...

Of course, it takes a long time to print such a thing, nevertheless there is a model for a printer, and of course for a laser in DXF format.Although the easiest way is to stick crocodiles into polystyrene, but as my practice shows, at the right...

In the leg itself, I also cut an M5 thread and simply screwed a hairpin with an inserted nut into the leg, it got a tight fix.Also added a model of the controller case cover with an additional hole for the connector. But I didn't print a new one, I...

... each time. My some other things: &nbsp;&nbsp; &nbsp; &nbsp; &nbsp;&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;

Or click Download once on the file Girl_Unicorn.rar My some other things: &nbsp;&nbsp; &nbsp; &nbsp; &nbsp;&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; ...