scale model

Some overhang areas in the inside don't bridge well, so you'll need to do some trimming / post-processing.Updated 5/2/2021:I added aluminum foil tape (HVAC duct tape, buy at any home/hardware store) for 3 reasons:serve as heat spreader so that the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 4 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 stencil_pattern_line_thickness = 30...

Not wishing to disassemble the printer, and even less to change the direction of rotation of the cooling fans of the LCD screen, I wanted to model a filtration system requiring no modification of the printer. The power supply of the fan is carried...

This fits in a 35mm (1 3/8") hole that you should drill in the rear-center of the unit Instructions My pipe had an OD of 60.5mm and I rounded up to 61 in the model. It's a great fit and I've included the SCAD file if you need to modify this diameter....

Did not want to spend a big amount of time 3D modeling a cable tie). What I like to do is build the whole assembly on a short piece of 90mm pipe (as shown) so I can comfortably work on my workbench. Then, by using a 90mm joiner section, I can simply...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 11 custom_back_extra_port_corner_resolution = 8 custom_bottom_fillet_radius = 1.6 custom_left_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

So, I made these 2020 fasteners.This is a remix of hallonhatt's: 3030 extrusions quick fastener:https://www.printables.com/model/80548-3030-extrusions-quick-fastener-fits-prusa-i3-mk3I printed at 0.16mm line height, 100% infill, with black Overture...

Print the model as is for the Front piece and MIRROR the part Z axis for the Back part. Position the part on its back with the legs sticking up, then rotate to 45 degrees to make it fit on your bed. Print the Front (part)... Then print the Back...

... fills the opening left after you remove the 12 volt adapter socket from the base. It simply slides into place. #Printing# I print rafts with most things, including these models, other than that they are quite simple and shouldn't cause any issues.

The source of the model has several parameters that you may wish to change. The current settings are for a silicone tube with an internal diameter of about 4 mm. You can adjust the pen length and width to your preference. Note that some tweaking may...

Probably the largest I could make it since I only have a Prusa Mini which they really need to add as a Printer Model option in the drop down. It's been out a year already. I still haven't shot this thing yet but i can load FSR and round ball just...

Taller models have a tendency to cool in the middle and pull the bottom up at the corners. If your workspace/office is 75 degrees and you printer is not in an exclosure you should probably use some kind of adhesive. I found Glass+Glue worked for me...

... most of these parts. If there are any tweaks necessary let me know. I have added a .step file of the assembled printer and I will upload a Fusion 360 back up file as soon as its processed so you guys can go nuts customizing the solid models.

When you warm the bags, the plastic becomes brittle, and you end up with loose desiccant. 3-4-2019 UPDATE: The cereal containers are 21 cup size and can be found at Amazon here:...

Start printing the parts (some of the parts need support).After you finish printing the Base, Hinge and the Main Stick you can start assembling the parts (use this 3d model for reference) , then insert the potentiometers to they're spots and wire...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Existing models didn't meet my needs, so I created a parametric part. The current parameters are tuned for use with an M6 thread and prior tapping. I recommend printing a test part (produced by setting debug = true) to ensure your tolerances are...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Tensegrity model maintaining stability with one single wire.Materials needed:0.5 mm nylon wire7x M3 nuts7x M3x10 mm Allen screws (longer ones were cut to the right size)wooden plank of about 55 cm2x 50 mm wood nailsThe spiral parts are designed to be...

I downloaded and printed two of the Flugzeug Halter - Breit STLs in the Model Plane Ceiling Hooks thing from dschiedsch. They worked but were a tight fit for some planes when I tried them out. That is when I decided to make something adjustable to...

The resulting "cylinder" is much stronger - I even tried to bend/break it without success. The hole piece was created with the following drafts and results : Bottom row, through holes (left to right) : 1/2° draft = very tight fit, very difficult to...

Since I mainly use it for soldering electronics, there is a situation where you need a slightly smaller scale to get an image, but it magnifies too much that only one SMD detail is visible on the screen with the microscope fully raised.The column...

There are also useful coat hangers and finger toys.Or just check out all my creations.Background on swatchesInsipration came from different swatch cards on thingiverse, all attached in the "remixed from" section on the Thingiverse model, and they...

Now it measures all points in Bed UPDATE Sept 29th Activated MPC Autotune for Nozzle https://marlinfw.org/docs/features/model_predictive_control.html. If you don't want to use it, the previous version is with PID Autotune, just don't update it</h3> ...

Winston sculpted reproduction of Schwarzenegger's face in several poses out of silicone, clay and plaster.[41] The sequences set in 2029 and the stop-motion scenes were developed by Fantasy II, a special effects company headed by Gene Warren...

The only sound comes from the layer fan.I have included the STEP files to facilitate remixes and alternative configurations.An associated BMG type extruder/carriage can be found here:...

---- ###Running the Customizer### Click the Open in Customizer button to create your own model on Thingiverse. Note that Thingiverse hadn't run their customizer queue from Jul 10, 2020 to Aug 4, 2022 and may stop running it at any time again. So...

Because I added Negative Volumes to the models, meaning the model will print with a wider hole in the center.Twist the entire leg assembly to drive the screw into the bottom of the table. As you drive the large leg screw into place it will snug up to...

I should snuggly fit with this model: https://www.printables.com/model/123074-ceiling-camera-mount-2-axis.03: Added the grow lights for indoor plants, see pictures. Also added a section describing the little differences. Earth anchor is good to go...