saw dust extraction 3d models

... ... Scale up the file by 2540% and print with 100% infill. Takes 45 minutes to print in vase mode at 60mm/s Push it in to the miter saw dust port. Very tight fit. ... Also compatible with the riving knife dust port on the 60v max table saw.

I made this to mount on my MS250 Delta Miter Saw to catch the saw dust coming off of the blade and redirect to the bag or vacuum. 2nd iteration and it fits and works very well. ...There must have been an original plastic piece on the saw but it was...

I created this adapter for the Dewalt 7491 jobsite saw (table saw). ...It allows you to use a 2.5 inch vacuum hose on the bottom port of the saw for dust collection. ... The inside of the adapter is tapered for a friction fit.

I created this solution because I was dissatisfied with the original dust collection on my Milwaukee Miter Saw. My preference in the workshop is to connect my vacuum directly to it, resulting in significantly less cleanup afterward. However, the saw...

A compact 10-inch by 11-inch dust collector designed for installation on a table saw. ...It perfectly accommodates the 2.25-inch diameter shop vacuum hose of Craftsman brand.

When the Dust Right hose is not connected, the is pretty much flat to the back of the saw vs using the Dust Right 4" to 2.5" adapter that sticks out pretty far and has to be held in place with hose clamps. If the fitting is too loose on the dust...

Dust cover plug for the Wen CT1065 track/plunge saw. Intended to close blade change hole, which focuses airflow to cutting area and maximizes dust collection. This cover is snap-fitted, easily removeable, and does not interfere with the plunge. ... ...

Replacement dust ports for Makita LS1219 mitre saw. Designed to allow two separate 50mm dust hoses to be connected to the top and bottom ports. Openscad files included to allow modifications for different sized hoses. ... May work on other models, if...

This elbow companion piece is designed to work seamlessly with the dust extractor found here:\r\nhttps://www.thingiverse.com/thing:2772652\r\nIt prints in two separate pieces that can be easily welded or superglued together, forming a secure...

... bolt for tightening. This is designed to fit the dust output of a Makita MLT100 saw. The other 99mm OD end is designed to fit inside the stock end of a Metabo SPA1200 dust collector. The Metabo end is slightly tapered so it stays on nicely. ...

Swap out the dust boot on your Harbor Freight 12-inch miter saw with a new one - just replace it, no need to worry about the 10-inch model since you don't have that one. ...The laser on this saw will still work perfectly fine, by the way, and it's...

This sleek Dust Collection Hood encases the saw blade, meticulously collecting every scrap of sawdust. With a compact printer at my disposal, I broke down the design into manageable pieces and expertly dovetailed them together, eliminating the need...

This adapter will allow you to downsize the bandsaw dust extraction port to fit the standard 35mm Ryobi shop-vac. This results in at least 95% of the dust from your cuts actually making it to your dust collector. It is very strong and fits snuggly....

It will keep dust from escaping through the side opening, thus improving dust collection.Be sure to check out slipangle28's remix made for dual extrusion.Print SettingsPrinter Brand:CrealityPrinter: Ender 3...

Nice dust cover for the Makita SP6000J plunge saw if you want to significantly enhance its dust collection capabilities. A simple yet robust design eliminates the need for any modification or screw.\r\n\r\nThe cover appears to be a factory part,...

Bosch Axial Glide Miter Saw Dust Redirectamajigger for the [GCM12SD](https://amzn.to/3mCvmMG) and presumably the [CM10GD](https://amzn.to/32RPnHn) *(affiliate links)* As seen on my dust-travel analysis video here: https://youtu.be/iDQSWgTmGFo Lately...

... sits against a wall. Modeled this so the saw can be up against the wall and the hose does not get in the way. 11/12/22 added a vertical port. Changed up the dust collection in my shop, worked better for me if angled up instead of to the side.

... wall. Modeled this so the saw can be up against the wall and the hose does not get in the way. 11/12/22 added a vertical port. Changed up the dust collection in my shop, worked better for me if angled up instead of to the side. ... Category: Parts

I built this attachment to install on my MS250 Delta Miter Saw, designed to catch the dust flying off the blade and redirect it into the bag or vacuum. This is my second iteration, and it fits perfectly, working flawlessly so far. ...Initially, I...

To assemble the adapter, simply remove the red composite ring from the original dust collection bag that comes with your saw and attach it to the printed component. The dimensions of the adapter match exactly the Bosch part where it fits into the...

Took inspiration from a previous design for the Dewalt 708 miter Saw Dust Assembly https://www.thingiverse.com/thing:612670 but the outlet nozzle on that was too large so started from scratch. Modeled in Blender (my first decent project). ... Updated...

Credit goes to Richard Crees and his YouTube channel for designing the wood and sheet metal version of the dust catch that inserts into the blade shroud of the table saw. You can see how it inserts and works on his video at...

The standard pivoting dust extractor adapter supplied with the Festool TS55 has a habit of drooping and can get in the way while sawing. I have seen other people selling fixed adapters but fancied having a go at making one myself. After much trial...

... ...I just liked the two-tone effect with the filler piece in a matching teal to Makita's accent color.TinkerCAD: https://www.tinkercad.com/things/6gSkfVuqmIk-makita-plunge-saw-dust-port-adapter?sharecode=4GqCFt8ve6i5MD2fvsQmqH42puuA5YIoyoovSc696BI

In order to reduce the greatest possible dust load on the saw blade lifting gear of the GTS10XC and to avoid premature wear, I have provided this with a protection. Disclaimer If you print this model and use it, you do this on your own risk. I...

Took inspiration from a previous design for the Dewalt 708 miter Saw Dust Assembly https://www.thingiverse.com/thing:612670 but the outlet nozzle on that was too large so started from scratch. Modeled in Blender (my first decent project). ... Updated...

This is a dust port for the Excalibur EX21 scroll saw. It mounts to the underside of the table like the stock one and uses three 9mm by 3mm thick round magnets to hold the far end. The magnets are not needed though. ...Four M3 bolts and nuts hold the 2...

Dust hood for a Ulmia 1710 table saw to fit a Festool 35mm vacuum hose. Modeled quick and dirty, but gets the job done well... You need a m5/m6 screw to attach it to the blade guard and another m6 to set the depth. ... You could insert a nut to secure...

I've been placing a bucket under my Rigid table saw to catch the majority of dust that falls through the dust chute. Dust bucket be gone!This is a reducer from 4" (table saw) to 1.75" (shop vac). Both my tools are Ridgid brand. Adapter is press...

- Saw Connector Test Fit: is the end that goes on the saw -- it should slide on with just a little resistance and should twist and lock securely onto the dust port's lugs. Hose Adapter Test Fit: fits over the 2.5" dust collection hose. This is...