sapphire plus firmware 3d models

5015 FAN DUCT and MOUNT for TWO TREES SAPPHIRE PLUS

Sapphire Plus Filament spool and tube holders for direct extruder      

Two Trees Sapphire Plus (SP5) BIQU H2 V2 Carriage/Mount

TWO TREES SAPPHIRE PLUS DIRECT DRIVE AND CABLE CHAIN CAP

*********************************************************************************** **Used Firmware for Hemera:** Those firmwares are preconfigured and (at least tested for the Sapphire Plus). The first one is using the standart Marlin UI. The...

Vent fan duct reduction 50-40 on side of Sapphire plus/pro

Filament spool and filament tube holders for 3D-printer TwoTrees Sapphire Plus with direct extruder mod

You will need 16mm Aluminium Pipe. ...200mm and 100mm.

LERDGE – pièces d'imprimante 3D, câble, chaîne de frein, outils de transport de fil, pont de fil en plastique Nylon ouvert à l'extérieur avec connecteurs d'extrémité 10*11 ...

PETG Extrudr

There are two versions, 1st version without nuts 2nd version with nuts BOM: 16x cylinder pins 2x8mm or 2x10mm 4x 3mmx3mm neodynium magnets 4x 4mm balls 8x M3x8mm (version without nut) 8x M2.5x12mm (version with nut) 8x M2.5 nut ...

Strand support in direct extrusion

You will need 16mm Aluminium Pipe. ...200mm and 100mm.

I redesigned the existing stabilizer to be more minimal. Recommended for ABL Users. ...Zendstop click cannot be mounted.

Had some troubles when printing the original one so i simply edited the filament hole to a more sturdy version. Tested and using it with the 3 pieces spool holder from the designer. Works like a charm! **You might touch to the filament guide if...

Kikkevil Maker!!!! Per chi vuole lasciare il gruppo hotend originale consiglio di stampare questo supporto. Il gruppo hotend sulla SP5 è bloccato solo su un lato provocando vibrazioni; per evitare tutto ciò, senza dover stampare gruppi interi...

This is used with a volcano hotend and it will mount the volcano higher than most other volcano mounts. The tip of the nozzle will be heigher than the rods on which the bed moves. You can use this mount with v6 or mosquito hotends but you will need...

A set of tools to help you make your printer square.Gantry_Y_Open/Close is meant to lock 90 deg between Y rails and the carriage. The difference is that Open allows to slide the carriage left/right a bit whereas Closed just locks completely. Print...

Been using on my printer for ages now, didn't like how complicated other designs were and also not regid enough. doesn't require any new hardware apart from a longer E motor cable. ...Can use existing BMG drive, Motor and mounting screws.

Designed up this mount so that the Direct Drive mount was not needed to be created with supports to add this as part of it. Clears the belts when homed and acts as a cable guide for the included split cable cover. Requires 2 new bolts to the...

SP5 REMIX MOUNT FOR H2 500C

Mount for 12 mm diameter static ABL probes (capacitive & inductive) for the TwoTrees Sapphire Plus (and likely S). Uses OEM mounting points and bolts (M2.5 or M3). If your probes came with washers, those may not fit, just exclude them from...

Mount for 12 mm diameter static ABL probes (capacitive & inductive) for the TwoTrees Sapphire Plus (and likely S). Uses OEM mounting points and bolts (M2.5 or M3). If your probes came with washers, those may not fit, just exclude them from...

Mount for 12 mm diameter static ABL probes (capacitive & inductive) for the TwoTrees Sapphire Plus (and likely S). Uses OEM mounting points and bolts (M2.5 or M3). If your probes came with washers, those may not fit, just exclude them from...

This file is a sapphire plus 3d printer platform model for cura slicer profile. ...Just to make it looks like a real sapphire plus part. The original model you can find here: https://grabcad.com/library/two-trees-sapphire-plus-3d-printer-1

Assembly will require: - M3 nuts - M3 x 8mm, 10mm, 12 and 16mm bolts - Narrow nose pliers - Knife - Flush Cutter - Drill 3mm for sanding M3 holes - Drill 1.5mm for fix X-axis endstop switch - Nylon ties for fixing belts - Blower fan 5015 adjusted...

Super simple mount for two trees sapphire plus without x/y volume loss. ...For fan duct I used https://www.thingiverse.com/thing:4662109

This is a support for the TP-link Tapo C100 camera, for the Sapphire Plus 3D printer. Only 2 screws and nuts "M4" are needed. ...

This is a support for the Autolev leveling sensor (or any similar 18mm sensor) for the Two Trees Sapphire Pro and Plus printers. ... It has cable guides at the top to improve the printer's cable management.