sander attachment for shop vac 3d models

To solve this problem, we designed a small attachment that allows you to connect a any wet/dry vacuum or dust collection system to your both the disk and belt sanders. The end of this attachment has a 2in (~54mm) OD and a 1.75in (~45mm) ID universal...

To solve this problem, we designed a small attachment that allows you to connect a any wet/dry vacuum or dust collection system to your both the disk and belt sanders. The end of this attachment has a 2in (~54mm) OD and a 1.75in (~45mm) ID universal...

This is an adapter for a Makita BO4550 palm sander that lets you hook it up to a ShopVac / shop vacuum. The BO4551 is probably very similar, so this might work on that too if I'm not mistaken. It fits tightly, and I couldn't quite figure out how to...

Used 2mm flanges.A series of Shop Vac 1-1/4 hose adapters I made to split a single vacuum into two feeds to a belt/disc sander. Has hose to hose (H2H) adapter, hose to sander (H2S), and a T connection in two pieces for easy printing. ...Simply glue the...

Adapter to hook up Makita BO4900V sander to Rigid 4000RV0 wet dry vac. ...The openings are 22.5mm (~0.8 in) and 45mm (~1.75 in), I went directly off caliper readings of the two hoses and it fit perfectly for me.

I have a DeWalt table saw and a DeWalt Shop Vac. ...This is an attachment so i can use the Shop vac on the table saw. Table saw end was about 2.5" shop vac end was about 1.75" Fits great, works perfectly. ...Snug fit on both ends.

Rigid Shop Vac Attachment Used for vacuuming Between the center console and Car seat

Shop-Vac Accessory Mounting Bracket: 31mm Shaft Attachment

I misplaced my connection for my Shop Vac. The intake port on this model is a standard 45mm diameter. ...Feel free to modify the design if you require a larger or smaller attachment.

... for my workspace. If you're looking for a reliable solution for printing on concrete floors, look no further than this shop vac attachment. ...It's the perfect tool for the job, and I'm confident it will serve you just as well as it has served me.

In this case, I wanted to use their compact shop-vac and random orbital sander together, but there was one problem - the hose from the vacuum wouldn't fit the sander. A 3D printer and a set of calipers make it incredibly easy to fix this issue. The...

Adapts the standard Ryobi sander bag connection to a 1.25" shop vac connection. Print in flexible filament with two perimeters and 15% infill to retain maximum flexibility without compromising vacuum. ...Optionally allows for a hose clamp to tighten the...

Connecting a Standard Shop Vacuum to an Aldi Workzone Disc and Belt Sander Ensure you have a suitable hose adapter for connecting your standard shop vacuum to the Aldi Workzone Titanium + Disc and Belt Sander. ...This versatile tool is available at...

My vacuum came equipped with an assortment of attachments, yet I found myself perpetually searching for specific parts due to the lack of suitable storage options available at the time of its delivery. Thankfully, the attachment holders boasted a...

However, they are remarkably sturdy, allowing for precise alignment and shared screw holes to minimize the number of screws required. I've successfully linked three of them together with sufficient clearance behind the attachments. Future refinements...

I've successfully linked three of them together, allowing for attachments with sufficient clearance behind them. Future modifications will focus on reducing the height of the cone and thinning its walls. This should result in faster printing times...

Prints upright without support. ...I recommend using a .8mm nozzle for a quicker, stronger print.

... my house. ...My old tool belt only held two 4V makita batts which did not work well with these higher voltage devices. A nice padded bag would allow me to carry the trimmer and keep my extra batter pack in there, ready for immediate use at a job site.

This adapter fits snugly over the 2.25-inch dust port found on many machines, accommodating the smaller 1.75-inch hose used in some Shop-Vac models. The measurements provided refer to the inside diameter of each fitting. ...A customized version of a...

I've been experimenting with this concept for some time now, and one of my initial designs was an adapter that connects a ridgid shop vac to a small hose.

Adapter built for an older, wired DEWALT sander. A buddy of mine misplaced his, so I decided to use my 3D printer to create a replacement. ...To save time, I set the layer height to 0.4mm and stopped printing halfway through, as the actual vacuum tube...

I've been using it with my BO5041 5" random orbit sander, but their other orbital and random orbit sanders seem to have the same square dust bag that this part requires. To use: Simply remove the original bag from your sander's bag connector and...

Hose adapter for a Shop Vac 2.27" ID to 1.75" ID Ryobi Palm Sander

Modified Stilwave's design to fit a shop vac. ... Designed for the Essentials by BaByliss for Men (7437EU) to fit a Shop Vac hose but might fit other clippers like Wahl, the curve shape looks similar?

Human: Hose nozzles with clips that hang from a 6-gallon RIDGID shop vac, model 6000RV0. Each attachment is 5 inches tall and securely attached to the 1 7/8 inch hose. One nozzle is centered, while the other is offset. This should fit any shop vac...

Shop vac adapter for 1 7/8in hose to Craftsman orbital sander. The adapter is friction fit to the inside of the sander dust port. The adapter also fits over the outside of the dust port to protect the channels for the dust bag. ...It also makes the...

Shop vac adapter for 1 7/8in hose to Craftsman orbital sander. The adapter is friction fit to the inside of the sander dust port. The adapter also fits over the outside of the dust port to protect the channels for the dust bag. ...It also makes the...

I came up with a solution for connecting my Bucket Head shop vac to my Harbor Freight belt sander in no time. ...If anyone wants to modify it, they can use the attached .stp and .ipt files.

This adapter converts a Ryobi VC100HD shop vacuum into a high-powered blower, utilizing the very same screw-on hose that's already attached for suction purposes.

Rigid Vac Attachment the Diameter is 2.5Inches/63.5mm This was built to intent to Vacuum In smaller Areas Like in between Car seat and Center console Please Send Feedback New to 3D Printing