samsung wireless phone charger 3d models

Samsung Wireless Charger Phone Stand. Very useful to use the phone while keep charging. ... Enjoy.

A stand for your Samsung Wireless (standard not the fast charger) charge and your Galaxy s6 or s7 phone. ...Print Settings Printer: PowerSpec 3D Pro (Flashforge) ...

The height of the charging coil was specifically positioned for the Samsung Galaxy S22 (that's the phone pictured), but hopefully it works for other phones. It may be too high for shorter phones, in that case I could design some additional spacers...

Samsung Wireless Phone and Samsung Galaxy Watch Charger Stand. Also has an option for holding your phone if you don't have a wireless puck. ... Also raised it up so you can put a cord under the stand for your phone if you don't have a puck

A stand for your Standard Samsung Wireless Charger, you can charge and use your smartphone in both directions. I made this remix because I can Work and Play games while it charges, and this was great! The arm has exactly 5mm that fits perfectly...

A stand for your Standard Samsung Wireless Charger, you can charge and use your smartphone in both directions. I made this remix because I can Work and Play games while it charges, and this was great! The arm has exactly 5mm that fits perfectly...

The original is great - I just needed room for a thicker phone (S7 in a tech21 case — that's about 11mm), and slightly changed the vertical base so that supports aren't needed. I think it can fit 12-13mm easily enough. I liked it slightly loose — if...

Samsung Galaxy S8 plus stand for wireless charger and phone. Thanks, Enjoy! ...

Samsung Galaxy S6/Edge phone & wireless charger holder, (for square charger) Print Settings Printer Brand: RepRap Printer: Prusa i3 Rafts: No Supports: Yes Resolution: 0.2 Infill: 25

Stand for samsung gear wireless charger and phone for beside or desk. ...works with the 44mm gear watch charger and a hugehave no worries if it needs to be remixed for other charger designs.

Simple charging stand for wireless charging pad for samsung. ...I printed it in a wooden PLA filament and looks beautiful.

Dock to fit in the EP-P1300 Wireless Charger from Samsung. Designed to fit my Samsung S21 Plus (with case). Angle of the dock is 45 degrees, so prints fine without support. ... There are 2 version, * V1: Original design *V2: Slightly refined...

Dock to fit in the EP-P1300 Wireless Charger from Samsung. Designed to fit my Samsung S21 Plus (with case). Angle of the dock is 45 degrees, so prints fine without support. ... There are 2 versions: V1: Original design V2: Slightly refined design

The wireless charger (7,98 €) for your phone can be ordered here: https://www.amazon.de/gp/product/B089Q5QN8F?ie=UTF8&psc=1&linkCode=sl1&tag=fotosrheinerf-21&linkId=17365c51448ea77f25cf06e40e210480&language=de_DE&ref_=as_li_ss_tl For the smartwatch...

I Made this Stand as my first design, for my LG G6 with Otterbox defender case this design still not ready, i got it wrong on height of Charger, and did not made enough space for cable to pass through, i had to cut cable to pass it through. it's a...

Not using stock samsung charger for the phone charging pad and therefore hole at the back for cable may be bigger than it needs to be or too small. I plan to make some minor modifications to it, for example the bit sticking up at the front I would...

A wireless charging dock for mobile phone. ...two adapters for Samsung charging pad and a generic small charging pad. The Charger Model for Samsung is EP-PG9201 with an outer circumference of approximately 96mm

A remix to allow Nothing Phone(2) to automatically sit correctly without sliding around on the wireless Samsung charger Print with: No support 15% infill FOUR walls to avoid infill pattern showing through 10mm brim to keep corners down. ... No printable...

This holder ensures that the phone is in the correct position on the wireless charger and does not fall off. It also dims the bright LED light while still being visible. When printed with transparent filament, the LED shines through, which gives a...

Phone stand for a Samsung Galaxy S7 (or similar) with integrated wireless charging. The wireless charing module was taken from a CHOETECH T511 charger...

Positions the phone at the center of the charger for reliable and optimal charging. ... Print in TPU with brim and supports.

... mount. ...It was designed to hold a Samsung Galaxy S8 to a computer monitor using double-sided tape. Search for "PeohZarr Wireless Charger" on Amazon to find a compatible wireless charger. ... Note: I have already included rafts into the design.

-Speaker amplifier -Wall-mountable cradle for phone -Works with Portrait and landscape mode -Perfect fit for this Qi Wireless Charger: http://smile.amazon.com/dp/B00G9W7YAW/ref=pe_385040_30332200_TE_item -For completeness, here is the receiver coil I...

Resized charging area to allow 97mm charger base instead of 88 mm Samsung one. All credit for design goes to previous creator. ...I just adjusted it.

This is a phone charger stand using a common 97mm Samsung Qi wireless phone charger. This will fit phone less than 85mm wide. I currently use it for a Samsung with an Otterbox cover. I printed this with the "free" Silver PLA shipped with my Mk3...

This is a phone charger stand using a common 97mm Samsung Qi wireless phone charger. This will fit phone less than 85mm wide. I currently use it for a Samsung with an Otterbox cover. I printed this with the "free" Silver PLA shipped with my Mk3 kit....

Samsung wireless phone charger is a snug fit, use a little bit force to get it in. The watch charger fits just fine. Just started with 3d printing and understanding Fusion 360. My first project. Just remix or improve if you're not happy with the...

Samsung wireless charger- Autodesk Inventor Professional 2019

The stand is for Samsung v1 wireless charger and Galaxy S7, but other phones my fit as well.

The stand is for Samsung v1 wireless charger and Galaxy S7, but other phones my fit as well.