samsung monitor vertical stand 3d models

Need to place your monitor or something else a bit higher. Just take these joints and connect 13mm aluminium tubes in betweento reach your desired lenght. The 13mm aluminimum tubes can be bought at the construction markets for a few Euros. Print...

No Hardware needed.Just put the raisrer Feet under the Monitor.The Front Feet are the same for all versions.There is space for rupper feet.3 Versions:Simple no Docking stationShort for docking stationLong for Docking station

... as the focal point. ...The printer-friendly creation requires M5 and M6 bolts for assembly. Crafted using 25mm square piping, it is compatible with makedaves monitor mount (excluding the wall piece) available at http://www.thingiverse.com/thing:22934.

I'm taking a trip down memory lane to my old gaming days, when I had three monitors set up and running simultaneously. The bezels on those screens were always getting on my nerves, so I took matters into my own hands and ripped them off. ...Little did I...

This is a straightforward printer stand that requires minimal effort. ...Simply print the stand's legs twice, then secure them beneath a wooden base of your preference using screws.

The base of my monitor is 195x195 so I made it a little bigger to have spare space to turn it or whatever. The height can easily be modified in any slicer just turn off symmetrical scaling and you can adjust z height to whatever you like. In its...

Podstavec pod monitor je tvořen dvěma vytisknutými díly (nohy) a jedním dřevěným prknem, pod které je možné schovat klávesnici a mít tak uklizený stůl. Parametry / parameters:tloušťka prkna / board thickness: 20 mmdélka prkna / board length:...

I modified this laptop stand to have a wider base in the back so you can leave your laptop open and it leans back just slightly without falling over. ... It leaves more space at your desk so you can still use your laptop screen as an extra monitor.

... 3 distinct sets below. Vertical Extension Optional Components: 4 x Three-Pronged Flat Pieces 5 x Five-Inch Rods 4 x Two-Inch Rods Horizontal Extension Additional Components: 1 x Four-Pronged Flat Piece 1 x Five-Pronged Rod 4 x Diagonal Support Rods

A compact stand designed specifically for a 24-inch Samsung monitor

Customized version of https://www.thingiverse.com/thing:5898536 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5898536

Customized version of https://www.thingiverse.com/thing:5898536 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5898536

Customized version of https://www.thingiverse.com/thing:5898536 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5898536

Customized version of https://www.thingiverse.com/thing:5898536 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5898536

Customized version of https://www.thingiverse.com/thing:5898536 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5898536

Customized version of https://www.thingiverse.com/thing:5898536 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5898536

Customized version of https://www.thingiverse.com/thing:5898536 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5898536

Customized version of https://www.thingiverse.com/thing:5898536 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5898536

Customized version of https://www.thingiverse.com/thing:5898536 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5898536

I designed this to mount a second vertical monitor in my setup. It is a work under development, I didnt finish printing all the parts yet, so i dont know how sturdy it will be. I am assuming it will be relatively stable. Use at your won risk. ...Use M8...

This is an connector designed for older samsung monitors.

As the monitor stand has built-in rubber grips, once lowered into position, the feet stay firmly attached. For use on smooth desks like glass or laminate, recommend fixing a rubber pad to each foot for increased grip. ... Also pick the right...

For use with vertical dual monitor arms such as: https://a.co/d/5RnXXso . ...The large tightener is for the table clamp and the small one are for the monitor arms.

The user is referring to a top-of-the-line computer monitor designed and manufactured by Samsung, a South Korean multinational conglomerate known for its innovative electronic devices. ...The term "LCD" stands for Liquid Crystal Display, a type of...

I created this smartphone stand based on a Samsung Galaxy S6. ...I drew inspiration from the jamesdeklerk model at thingiverse.com/thing:615588.

3d model of monitor Samsung S24E390HL. ...Size: width 54.8 cm, height 40.9 cm, depth 18.2 cm.

A simple over the back mount to allow an iPhone to be positioned vertically so its forward facing camera can peek over the top of a monitor about 2 cm. This allows applications like Animaze to use the True Depth forward facing camera for face...

I designed a custom adapter wall mount for my Samsung monitor because it lacked a VESA mounting point on the rear, so I opted to attach it directly to the base of the monitor instead.

I have a couple Samsung U28E590 monitors and lost one of the base mounts for the monitor. ...Print this out and then screw a 1x2 piece of wood to the bottom to finish the mount.

I'm holding onto my Samsung S10+.