samsung galaxy tab wall mount 3d models

Simple wall mount for Samsung Galaxy Tab 3 (SM-T210) 7 inch, portrait orientation.

A wall mount for the Samsung Galaxy Tab A8, at an angle of 60 degrees, with two accessible screw-holes to attach directly to a wall.

Needed a Wall Mount so created this In two parts (Printed face down with Bed support) For my Samsung Galaxy Tab A8 10.5”

For tablet (Samsung galaxy tab 6) for user interface home assistant. Speaker holes on both sides. ... After completing add some padding in the bottom corners and at the top for a snug fit without damaging the tablet.

This wall mount holder is designed to keep your tablet on a wall for a smart home system.

I had to secure a tablet against a wall, allowing me to closely monitor all of my sensor readings directly through the OpenHAB app. ...The setup should also function effectively with other tablets of comparable dimensions.

I Designed this tablet holder for my friend's smart home system. He wanted a holder that will keep the tablet in place and hide the cables. If your bed adhesion is good you can print it without rafts. ...I used rafts because of my low bed adhesion.

Installing a wall mount for my Samsung Galaxy Tab 2 tablet, I carefully placed it within a specially designed housing that allows charging to take place even when mounted on the wall. The setup requires minimal button access since my home automation...

Simple wall mount for a Samsung Galaxy Tab A 8''. ...I stuck it to a fridge with double sided adhesive tape.

I got a Galaxy tab as a promotional gift and I'm turning it into a valuable asset for my home automation system, so I designed a sleek wall mount that blends in seamlessly. It's destined to be the crown jewel of my collection and its design must make...

This is a minimalistic wall mount for the Samsung TAB A8 that prints without support and all the pieces should snap together without any modifications or glue.Everything else should be self-explanatory with help from the images  I could not...

To securely attach my vintage Galaxy Tab onto the kitchen wall, I created four replicas and fastened them using screws. ...The outcome was outstanding as it functioned flawlessly.

Print as is, no supports needed, mount with command velcro strips

Mounting can be done normally with 4 screws. On the upper side, a small hole has been left open with which the tablet can be restarted without taking it out of the box if necessary. ... # Support my work <a...

Couldn't find any full closed wall mount for Samsung Galaxy Tab S2 8", so i created it. Tablet will be used as Smart Home centre for home automation, thermostat controll, and for Google Home. Added holes to speakers and microphone and cut for...

Remix to adapt dimensions to my Samsung Galaxy Tab A7 Lite (SM-T225) with its protective case.USB port position was wrong on the first print, I have not re-printed it since modifying.

This 3D-printed wall mount for the Samsung Galaxy Tab A was created as an alternative to existing metal and expensive options, which are often tailored only for iPad.It's designed for practicality and can be used in various settings like meeting...

Wall mount designed for the 10.5 inch Samsung Galaxy Tab A8 released late 2021/early 2022 (depending on region). Primarily intended for use as a dashboard with home automation systems such as Home Assistant, Hubitat, ActionTiles etc. Designed to...

Wall mount for a Samsung Galaxy Tab S 8.4 tablet. It has a couple of mounting holes intended for use with a one gang electrical box, but I suppose you could drive screws into drywall anchors through them, too. I designed this part to hold an my old...

Wall mount for a Samsung Galaxy Tab S 8.4 tablet. It has a couple of mounting holes intended for use with a one gang electrical box, but I suppose you could drive screws into drywall anchors through them, too. I designed this part to hold an my old...

Hi, This is a WallMount for a Samsung Galaxy Tab A8 (2021) model SM-X200. Five screw are needed. One to close de case and fourto fix the case on the support. I printed it on an Alphawise U20 with supports (see print settings section). The...

Two piece wall mount for Samsung Galaxy Tab A8. ... There is enough clearance for front facing camera and brightness sensor to work.

I designed this wall mount so I cold mount my Galaxy Tab A7 on the wall to display HomeAssistant dashboards. The mount is attached to the wall using double sided nano gel tape which doesn't wreck the walls and is easily removable but super strong.

I was missing a solution to mount my tablet that we use for Home Assistant in our apartment's living room, so here is my example for a "hopefully" perfect fitting frame'a'like wall mount for a Samsung Galaxy Tab A (2016) SM-T585. I originally...

Wall mount designed for the 10.1 inch 2019 Samsung Galaxy Tab A (model number SM-T510). Primarily intended for use as a dashboard with home automation systems such as Home Assistant, Hubitat, ActionTile etc. Designed to use a readily available 90...

First Part for a Samsung Galaxy Tab 3 10.0 wall mount with push unlock- Not Tested Tab 3 10.0 v7 + Tab 3 10.0 Wall Mount V3 or Wall mount v5 or Wall mount v6.stl Tab 3 10.0 v14 + Tab 3 10.0 Cover V4 (+ 2x nuts cover v1) + Wall mount v5 or Wall mount...

First Part for a Samsung Galaxy Tab 3 10.0 wall mount with push unlock- Not Tested Tab 3 10.0 v7 + Tab 3 10.0 Wall Mount V3 or Wall mount v5 or Wall mount v6.stl Tab 3 10.0 v14 + Tab 3 10.0 Cover V4 (+ 2x nuts cover v1) + Wall mount v5 or Wall mount...

First Part for a Samsung Galaxy Tab 3 10.0 wall mount with push unlock- Not Tested Tab 3 10.0 v7 + Tab 3 10.0 Wall Mount V3 or Wall mount v5 or Wall mount v6.stl Tab 3 10.0 v14 + Tab 3 10.0 Cover V4 (+ 2x nuts cover v1) + Wall mount v5 or Wall mount...

- Standard Version - Printable on printers with larger printer area > 30 cm - Files: - Standard_Version_Lid.stl - Standard_Version_Wall Body.stl - Standard_Version_Samsung_Galaxy_Tab_A7_SM-T500_Wall_Mount_v19.step - Splitted Version - Printable on...