safe shelf clips 3d models

Inspired by and remixed from rumeadors shelf clip. Enlarged and tweaked to fit metric rack with 10x3mm holes spaced 20mm apart. Also, simplified to be easily printable without any supports. ...I used PLA or PETG, both viable options.

This shelf is designed specifically for the Kaso E2-250 Safe, featuring dimensions of 600x400x15. ...The sheet has a thickness of 1.5mm and boasts a sleek RAL 7035 Shiny finish.

This creation was designed using Tinkercad's innovative platform. ...The shelf clips it features have been thoroughly tested and proven to be extremely effective.

Just a basic clip I made to add shelves to my desk, I originally made it to use a 3d printed shelf but seemed a wasted of material and time when I have tons of old card board boxes :) Turned out great for old boxes and the clip was designed to fit a...

The remix is designed for four clips printed on their side in a mirrored pattern, with two sets of two clips pointing outward in opposing directions. This configuration allows you to easily convert the support to a backer without having to remove it...

... ... Print Settings Printer: Anet A8 Rafts: None Required Supports: Not Needed Infill Density: 10% Notes: For a complete setup, print two of these clips to hold your stationery securely in place. ...They are designed for hanging items off, too.

I crafted a knife holder that clips neatly onto the underside of my safe's top shelf. ...It's specifically designed to hold four knives per holder, with two holders positioned side by side for maximum storage efficiency.

This is a replacement shelf bracket for Sports Afield safes.

There are two options, one with screw holes (for folks who want to screw it into something) and one without (for folks who want to attach it to a safe with Velcro, or to place them on a shelf. I shopped around for something similar, and they were...

... angle. ... This custom part was designed to hold a gun or folder shelf within a safe, providing secure storage for valuable items. ... To accommodate this part, the nose holders should be spaced approximately 148mm apart with a minimum size of 11mm.

My glass TV Shelf was held in place with some little Y-Brackets and my kids would pull the glass right out and make it fall. I designed these to constrain it in all directions. My setup required 4 lower brackets and the two upper brackets. The center...

My glass TV Shelf was held in place with some little Y-Brackets and my kids would pull the glass right out and make it fall. I designed these to constrain it in all directions. My setup required 4 lower brackets and the two upper brackets. The center...

Each clip requires a 6-32 machine screw (a fillister head works perfectly) and a matching nut (so four bolts and nuts are needed per shelf). First, slip the nut into the pocket, making sure one corner leads the way. ...Next, hook the clip around the...

These are replacement clips for the Elfa wardrobe system, used to fasten the shelf.They clip on perfectly.The original got brittle and broke, so i made new ones based on the old measurements.Printed in PETG with 0.2 layer height and 80% infill.

Replace a damaged refrigerator shelf restraint with 3D printed clips. After relocating to a new apartment, I discovered my bottom shelf was missing its restraint. Utilizing OpenSCAD and MakerBot, I created two different clips for the left and right...

I designed these for my filament-shelf with 20mm aluminium pipes (https://www.thingiverse.com/thing:4513536). Simply click them on the pipe and see what kind of filament is on the spool above it. I used different colours of filament for different...

Printing support structures weren't required or needed; the setup is designed to avoid those during the print process.\nIn this clip set-up for a display shelf with 6-7 inch action figures, the spacing and position of each horizontal rod were...

These clips are for covering the front of shelves and displaying your vinyl collection. the clips are made for ikea Kallax shelving units. ...NO SUPPORTS NEEDED.

This clip replaces the original clips that come on the clothes horse that become brittle in the sun.Print it at 100% infill with the open end down, I found that I could print a bunch at the same time without too many issues.Since it is a mechanical...

These are shelf supports designed specifically for a Stack-On GCB-900 safe. I've researched some reviews of the shelves, which revealed concerns about their weakness and tendency to bow or cave in over time due to excessive weight. As a precautionary...

This model is made to replace some old shelf clips. The dimensions are 38mm x 12.2mm x 16mm. ...It was made for wire shelving with a diameter of 6.5mm

The Suncast Vertical Shed wire shelf plastic clips will degrade and fall apart over time. I modeled replacement clips of various lengths in 2mm increments because the holes don't always line up. I also recommend replacing the screws with stainless...

... one for UTC, which is helpful in my Ham Radio hobby. For other shelf clips in this family, see: https://www.thingiverse.com/thing:3804566 https://www.thingiverse.com/thing:3707116 I've included the Sketchup files in case you want to modify it. ...

Displaying a lot of small items in the shelf but they come with only 4 levels. Tried few existing designs if found them unsatisfactory and decided to redesign. EDIT: 18/02, wrong files uploaded originally. ...corrected

Displaying numerous smaller items on a four-level shelf proved less than ideal. ...Several pre-existing designs were scrutinized but ultimately deemed unfulfilling, prompting a complete overhaul of the concept.

This is a remix of Deen0X's bed glass attachment clips that's 100% head-safe, meaning that it won't cause the print head to hit the clips when printing around the borders of the build plate. ... For information about usage, simply check the pictures...

safe

super safe

Two layer safe distance between this layers 10mm

A model of a safe constructed specifically at the behest of Yom.