s 360 12 3d models

The 80mm Fan Cover is a crucial component designed specifically to shield the S-300-12 PSU on Tevo Tarantula models and other similar printers. ...Its compact design allows it to fit snugly over the power supply unit, providing optimal protection...

... S300-12 power supplies. ...Since I built this cover for my ham radio power supply, it's optimized for the standard 13.8V output. The design also fits other similar power supplies with dimensions 110x50mm. ...It's crafted from PLA or PetG materials.

This is a cover for the S-400-12 Power Supply for a Prusa I3 MK2. ...License GNU GPL v3<br/> This is a modified Version of the openscad file von J.Prusa<br/> The mount holes on the frame need to be changed.</p>

Secure your 80mm and 92mm fans with the S-250-12 bracket and fan mount. The front bracket features two mounting holes designed to hold the power supply in place using M3*8 screws. To attach it to the board, simply drop M3 nuts into the designated...

This is a Children's Table and Chair Set at 1:12 Scale. Based on plans from Woodsmith Issue 56. ...Recommend printing the separate Table and Chair files for better definition and much less support requirement, however the complete set is provided in a...

Developed exclusively for Gray & Pape Inc., this innovative 3-D model was meticulously crafted to facilitate effective mitigation strategies during the removal of two lock tender's houses at Kentucky River Lock and Dam No. 12. Their demolition is a...

PSU and switch cover for the S-480-12 model. You will need: 2 4mm screws (not metric) 1 3x10 screw (metric) (other sizes may apply, I used these) The compatible switch is shown in the picture. v2 eliminates the cover's interference with the...

... version of this PSU. With OpenSCAD's limitations now starkly apparent, I've been forced to abandon my vision for a more intricate design. As a result, the scad-file attached is an unpolished representation of my Anycubic I3 Mega's PSU S-300-12.

The plan is to bolt them directly to the rear of your power supply (S-180-12 PSU), then you'll need to drill countersinks into your mounting panel where the screws protrude. After that, simply attach this to your panel or board. ... I use these mounts...

I created a protective casing for the S-300-12 power supply to enhance input protection and aesthetics. A relay has been installed inside to switch on/off the power supply after pressing the red toggle switch. The enclosed Solidworks file enables...

Some sly critter keeps yanking out the feeder slots from my Wild Bill's 12 station bird feeder. Most days I track them down in the yard, but sometimes they vanish into thin air. Frustrated with constantly reapplying duct tape to seal the gaps that...

I started with a base for a different wireless charger that looked like it could fit the iPhone 12 Pro. This is the result. It might work for other iPhones as well, I am using a 12 Pro. I also don't know for sure that it will work in a Model S but I...

I started with a base for a different wireless charger that looked like it could fit the iPhone 12 Pro. This is the result. It might work for other iPhones as well, I am using a 12 Pro. I also don't know for sure that it will work in a Model S but I...

Here is the rewritten text: I've created a custom PSU for S-180-12 with dimensions of 199x97x42, tailored to fit the 3030 profile perfectly. This design was inspired by the Original Prusa I3 Mk2 and features a sleek, compact layout. One of the key...

A "Remove Before Flight" can be added to provide additional visibility when installed.Designed specifically for Van's Aircraft RV-12.Print using ASA or any UV resistant filament. ...The small slot may require clearing with a small (precision) flat file...

S-240-12. The IEC connector used in this cover is standard, sourced from an old PC power supply, while the switch is a rectangular rocker switch also taken from the same unit. A triangular prism brim surrounds the cover to prevent warping and...

... arcade control panel. ... Prints without supports at 0.2mm layer height. GRS Spinner - https://www.amazon.com/ThunderStick-Arcade-Spinner-for-Arcade1Up/dp/B07P5WJ7BC 12-in-1 Board - https://www.amazon.com/Arcade1Up-12-1-Interface-Board/dp/B07NKJ3SKH

Jwizard’s Decorative Cylinder #3 – 3/12/22 Designed by JWizard Thank you for choosing the JWizard’s Decorative Cylinder #3! Our decorative cylinders can be used add to a rooms décor or to store all kinds of items. Now you have a place for your...

This is a Rudder Pedal Lock for a Van's Aircraft RV-12. The 3D printed part is a curved "foot" that accepts a 1" (id) Schedule 40 PCV pipe section. The foot goes against the back of the pilot or co-pilot footwell while the PCV pipe goes around the...

I fell deeply in love with RobSoundtrack's 12-hole Ocarina and was thrilled by its exceptional playability! However, my Nordic roots made me feel that it required a touch of elegance :D So I painstakingly traced the actual artwork from The Jelling...

360 Brake

Caméra 360°

Caméra 360°

Eleni’s Boba Rabbit Box – 3/12/22 Designed by JWizard Thank you for choosing Eleni’s Boba Rabbit Box! Eleni’s Boba Rabbit Box contains a rabbit on each of the sides and the top of the box. This box has rounded corners on the outside and inside of...

I designed a PSU cover for the S-180-12 unit that came with my printer, which would keep it standing upright on my desk with the cord facing away. After searching in vain for one that actually fit, I made this myself. I created some custom...

I am modeling a Wanhao power supply using Fusion 360. The printer has been modified with a Zbrace mod and is now situated on two 2.5mm rubber feet. ...To secure the power supply, six 3mm x 12mm screws are required, accompanied by two 3mm nuts and two...

Ein Halter um ein lüfterloses Meanwell UHP-350-12 an den originalen Befestigungen zu verschrauben. Bitte die Datei zwei mal drucken. ... Zur Befestigung benötigt Ihr: 4x M3x16 oder M2x20 4x Beilagscheibe (Washer) 4x M3 Muttern (Nuts) Viele...

It fits S-240-12 PSUs and allows you to install a rocker switch socket like the one shown in the attached picture. It doesn't require any supports, brims, or additional features. The inside is reinforced for added stability. I recommend printing on...

Eleni’s Greek Triangle Bowl – 10/12/21 Designed by JWizard Thank you for choosing Eleni’s Greek Triangle Bowl! We used the same Greek design that we used earlier with Eleni’s Greek Triangle Vase. Since we printed Eleni’s Triangle Vase in Matte Navy...

This is a Rudder Pedal Lock for a Van's Aircraft RV-12. The 3D printed part is a curved "foot" that accepts a 1" (id) Schedule 40 PVC pipe section. The foot goes against the back of the pilot or co-pilot footwell while the PVC pipe goes around the...