rx8 gauge pod 3d models

I've been using this 3D printed gauge pod in my 1998 Subaru WRX for several years now and it's never given me any problems. The gauge pod in my photos has been sanded smooth after printing and coated with satin black paint. I previously shared this...

Triple gauge pod for Subaru Justy. ...This should work with any 1-1/2 inch gauges but these are the ones I used: https://www.oreillyauto.com/detail/c/equus/equus-1-1-2-inch-triple-gauge-kit/equ0/6100?q=Equus+1-1%2F2+Inch+Triple+Gauge+Kit/ Installation...

52mm gauge pod for all automotive use, snug fit from printer no need for sanding. ...20mm hole at the back for hose and wiring, can be mounted with double sided tape or can be drilled into base.

66 mm gauge pod for all 66 mm guages fits without sanding. Will stick to any flat surface with double sided tape. perfect for any automotive use. ...Quick and easy to print.

... ...The design might involve a double or triple pod configuration. In total, three gauges are to be installed in the glove compartment, displaying oil pressure, air/fuel ratio (AFR), and water temperature, all of which share the same standard size.

... ... Oem part number: 45286-53901 Valid for Toyotas and Lexus models: Is200/300 Altezza Gs300/340/400 Mark 2 Celica 52MM Gauges pod on ignition barrel cowl plastic trim surrond stalk column. Material: PLA, recommended ASA Printing: 3h with supports.

I've been running with 2 gauges zip-tied to the outside of the single pod for probably a year now and finally got around to remixing into a triple pod to clean it all up.I'm not the best designer, so it isn't perfect, but it works! 2 of my gauges...

This is a precision gauge pod, distinctly Scandinavian in design, evoking a strong "wow" factor.\r\n\r\nIt was engineered to fit extremely snugly on a 52mm gauge, and I highly recommend printing it at approximately 102% of its original size for...

Single gauge pod for the newest body style Sierras and Silverado trucks. Used to mount Banks gauge for Derringer and Pedal Monster data. These STLs mount to upper vent of the driver side panel. This is a work in progress and I will be...

this is a 60mm and 52mm pod. ...you will have to run the wires through the back once you put the gauges in they will not come out. i had to use a heat gun to soften the plastic to push the gauges out to connect the plugs.

I reengineered pschiptuning's single gauge pod mount design to make it stronger, with a 3mm wall thickness, and a deeper profile. I also added a rear plate to conceal the back of the gauge. ...You may need to lightly sand the interior like I did to...

I conceptualized a triple gauge pod for my 1987 Ramcharger build, intending it to be versatile enough for any 80s Dodge truck model. The engine roars loudly, while the factory radio gave out years ago, necessitating a prominent and clean location for...

This is a remix from https://www.thingiverse.com/thing:1832214 I really liked the original design since it allowed me to put my gauge anywhere I wanted and no other companies make any "formed" pods for my vehicle. As my vehicle's engine build grew, I...

Valid for Toyotas and Lexus models: Is200/300 Altezza Gs300/340/400 Mark 2 Celica 52MM Gauges pod on ignition barrel cowl plastic trim surrond stalk column. Material: PLA, recommended ASA. Printing: 3h with supports. ... @xdash_211 If you liked it...

... pod can still be removed. This has been tested with a SAAS trax gauge for fitment (currently cannot confirm other brands) Secure pod to the bracket with a M5 bolt and nut. ... *Added a new mount to match the width of the tape for easier install

i had a problem with my fiat seicento not having a tachometer and temperature gauge so i installed a pair but i couldnt fined a good mounting solution so i maid this universal gauge pod and installed it where the stock tachometer goes i hope it fits...

I printed this in ABS at .1mm resolution and strongly recommend using a raft or brim for the gauge pod to ensure a secure fit. A raft is unnecessary for the base. To add strength, I used 50% infill in the final design; you may be able to get away...

This is a gauge pod I designed for my 2005 Silverado 2500. It's the cubby just below the center dash vent. Not on all Silverado's though. Once you remove the old cubby, you need to remove the old clips which can be a pain. But are necessary to a good...

Just a small easy plug for the $25, 3 gauge pod from 42draftdesigns.com designed for the VDO gauges to sit flush. So instead of inserting a gauge you can pop this filler right in and it will sit flush just the same. Its just a tight press fit. I'd...

A quick tip for anyone looking for a simple solution to make their VDO gauges sit flush - check out the $25, 3-gauge pod from 42draftdesigns.com. This nifty little filler is designed specifically for VDO gauges and can be easily popped in instead of...

This is a pod designed specifically for a 60mm turbo boost gauge in a Fiat Coupe 20vt. However, it can easily be modified to fit other vehicles. I needed a way to mount a gauge without compromising the car's interior by drilling or cutting. The...

I don't currently require a gauge pod, but this seemed like an engaging OpenScad challenge, so here's what I came up with. It might print as-is with powder printers, but for FDM printers you will likely need to divide it into two or more sections...

pod mount for a mj/xj

This is a 2-1/16" gauge pod designed for mounting to a 45-degree slanted roll cage with a 1.665" OD. I used three of these pods on my roll bar setup. To assemble, print out the design and head to a hardware store to source suitable bolts or screws....

The gauge is set to measure.

A 60mm by 18mm sized housing specifically designed to accommodate a gauge.

This is a straightforward instrument cluster with a basic gauge display, lacking any elaborate features.

Single A pillar gauge mount fits for Bmw e36 coupe. ...It brings you an unique design and look to you interior. Perfect angle for driver (LHD). You can download once and print it multiple times if you add more gauges.

This print replaces the center vent on a honda DelSol dash to mount 3 standard size (52mm) gauges

YARIS dash vent Gauge yaris, yaris gr, yaris hybrid, yaris cross 62-60mm gauge = 60mm with tape 52mm gauge with adapter in stl" 2 stl * left steering wheel "air vent gauge" (stl) * right steering wheel "air vent gauge" (stl) * second gauge if you...