rx 580 backplate 3d models

This replacement wheel and tire is designed for the 3D Hobby Slick 580, but it can be used for a wide range of aircraft models. The wheel was printed at a layer thickness of .2mm with 100% infill density. I used PETG as the print material. The tire...

The Convair CV-580, a popular medium haul transport plane in the '60s and '70s, was built to replace the CV-340 and Martin 404 models. This aircraft featured Allison Turboprop engines, providing increased power, speed, and efficiency compared to its...

The Convair CV-580 was a widely used medium haul, medium load commercial aircraft in the 1960s and 70s. It operated with major and regional airlines until the late 70s and early 80s when it was replaced by jets like DC-9 and 737s. Intended for...

The Convair CV-580 was a prominent transport aircraft for medium hauls and medium loads in the 1960s and 70s, operating with major and regional airlines until the late '70s and early '80s when they were replaced by jets like DC-9 and 737s. Designed...

The Convair CV-580 was a very popular transport aircraft for the medium haul medium load commercial airlines in the 1960s and 1970s. It was active with major and regional airlines until the late 1970s and early 1980s when they were replaced by...

Available in various formats, this model represents the popular Convair CV-580 transport aircraft. Used by commercial airlines for medium hauls with medium loads during the 1960s and 1970s, it continued its service with major and regional carriers...

The Convair CV-580 was a popular medium haul, medium load transport for commercial airlines during the 1960s and 70s. It remained active with major and regional airlines until the late 70s/early 80s when jets like DC-9 and 737s took over. Designed...

The Convair CV-580, a prominent medium haul transport aircraft in the '60s and '70s, served major and regional airlines until the late '70s and early '80s, when jets like DC-9 and 737 took over. Despite being replaced by jets, it continued to serve...

The Convair CV-580 was a prevalent medium haul transport aircraft for commercial airlines during the 1960s and 70s. Major and regional airlines operated it until the late 70s and early 80s, when jets like DC-9 and 737s replaced them. Designed to...

The Convair CV-580, a popular medium haul transport aircraft in the '60s and '70s, was used by major and regional airlines until the early '80s when jets like DC-9 and 737s took over. Designed for smaller carriers as replacements for CV-340 and...

Available in various formats, this model replicates the Convair CV-580, a popular medium haul, medium load transport aircraft for commercial airlines during the 1960s and 70s. Operating with major and regional airlines until the late 70s and early...

The latter I could find here.Sadly I found no suitable backplate so I whipped out Fusion and made one.I recommend you to print with something more temperature tolerant. ...I chose PETG for mine.</p><p>It still has a problem with it bending the...

This is a simple backplate using the same dimensions as the puzzle itself.The square in the center has a very slight recession to allow ample space for numbers to slide over while leaving the edges raised enough to adhere around the edge of the main...

I designed this custom backplate to securely hold an ATX power supply in any cabinet, serving as a reliable power source for my Bluetooth speaker project. This versatile design can easily adapt to suit various other applications or projects. The...

#Ender 3 V2 Chain Backplate# **This is a WIP, fixing some dimensions and extrusions.** An adaptable backplate for the Ender 3 V2 allowing users to use the chain from: "johnniewhiskey" [Ender 3 Cable Chain](https://www.thingiverse.com/thing:2920060)...

To secure the backplate simply heated up the scraper for your 3D printer with a hot air gun and melt the posts that go through the mounting holes. Bit more work but once it is done they are solid. These are specifically designed for GPURiser.com...

To achieve a two-tone effect on my backplate, I employed a technique where I switched filaments during the print process after the letters had started printing. ...Utilizing Prusa Slicers' color print feature allowed me to seamlessly blend the colors...

It is 0.5mm thicker than the original aluminium backplate to give it some stability. ...Note that this will not block RFID, this can be great if you store a access card and don't want to remove it to use.</p><p>No supports needed.</p><p>&nbsp;</p><p>If...

A backplate for the HP Reverb G2. You can glue some foam on it and stick it into the headstrap. I have the G2 set to the smallest size and it is a little too loose so i designed this. ... Maybe this Airsoft helmet pads are working: ...

This is a backplate designed to match the dimensions of the Nilight - 90015A Battery Switch from Amazon.com. When mounting the switch on a battery box, this prevents the nuts from rubbing on the battery and causing potential issues. ...You just need to...

I designed this backplate for an Asus A58M-E motherboard using Inkscape and transformed it into 3D form with Tinkercad. Alongside are the STL file exported directly from Tinkercad and the SVG file generated by Inkscape. ...The fit is a bit snug, so you...

Backplate I made as an addition for the GA Hunter files. It's scaled up slightly to fit my particular build but can easily be scaled down, just be sure to check your measurements. ...I attached mine with CA glue and modeling putty.I've built it as close...

Hi, I made this backplate to help me mount custom cooler designs on my lga 1366 motherboard. The holes are intentionally small so that the screw cuts its own threads when inserted. ...I printed this with 0.12mm layer height and 20 percent infill, no...

Designed this component after the authentic pump found in the Iceman Chiller, and I'm using a similar setup to secure the attractive backplate in place. ...Initially, I intended to use the integrated pump, but unfortunately, it malfunctioned, so I had...

Backplate/enclosure for Melzi Arduino on RepRap Huxley printers, featuring cable management. Assemble with glue; prints include Huxley-specific mounts, but can be customized for other boards. Requires M3 screws, wood screws (3/3.5 mm) for mounting. ...A...

Square-shaped cpu backplate for LGA 115X sockets (1150/1151/1155/1156...) and probably other sockets not mentioned (the clearance is 75mm between each point). ... There are two versions, one flat and the other spaced with 3mm of travel with the...

Square-shaped cpu backplate for LGA 115X sockets (1150/1151/1155/1156...) and probably other sockets not mentioned (the clearance is 75mm between each point). ... There are two versions, one flat and the other spaced with 3mm of travel with the...

Mini-square-shaped cpu backplate for LGA 115X sockets (1150/1151/1155/1156...) and probably other sockets not mentioned (the clearance is 75mm between each point). ... There are two versions, one flat and the other spaced with 3mm of travel with the...

I rebuilt the backplate with a strategically placed hole that allows the network cable to protrude freely. In the image provided, the USB port and power switch are situated off-center. ...I revised this design to ensure a smoother insertion process for...

Backplate for a 2.5" version. Fixes the clock in place so it can not rotate and provides support for standing it straight up. ... Has different positions so you can choose the standing angle you prefer Blender file included if you want to make...