runcam swift 2 3d models

The side plate is designed to integrate seamlessly with the Runcam Micro Swift 2 camera and the TX220U transmitter, all without requiring any adjustments or interference from the flight controller itself.

It's tailored to pair perfectly with a Qav210 frame, specifically designed in combination with a Runcam Mini swift and a 2.5mm GoPro lens! Standoffs are precision-made at 30x6mm and slide smoothly over them. The angle is securely fixed with two...

Rancam 5 im Golfball PLA+ 2 Wände Unten/Oben 3 Lagen Füllung Gitter 10% Linien verbinden https://www.youtube.com/watch?v=pAqguaNBjRg

This is a Runcam Swift Micro camera mount for the Hyperlite Floss v1. Printed in TPU with 100% infill. Other Floss swift micro mounts were too flimsy for me so I made my own. It slips around the 5mm standoffs and is 25mm tall. Screw the camera to the...

Naked camera for light FPV drones with 2.5-4inch props. ...Total weight with all screws and nuts is 25 gramms, may be this is the lightest 4K camera with gyro and good video quality.

Naked camera for light FPV drones with 2.5-4inch props. ...Total weight with all screws and nuts is 25 gramms, may be this is the lightest 4K camera with gyro and good video quality.

http://www.thingiverse.com/apps/customizer/run?thing_id=1015101 Using the following options: Hole size is set at 3.2 Rear CC is fixed at 35 millimeters Edge margin is precisely 3 millimeters Solid wedge option is disabled Velcro height is optimized...

This is an aerodynamic holder designed for cameras such as Mobius/Mobius Mini/Mobius Maxi/Mobius 2/RunCam2/Foxeer Legend 2/Foxeer Legend 3/GitUp F1. I've tested these cameras and the holder fits perfectly, likely suitable for any flat camera model.

A friend of mine wanted a mount for his toothpick which used the top of a tinyhawk 2 so here it is. TA DA! I printed this on my Creality CR10S Pro V2 with 100% infill but that's just what I do with TPU prints, retractions disabled and set to 228c...

... print it out. Avoid attempting less than 15% infill, or it will likely break while cleaning away support material. Print Settings Printer Brand: RepRap Printer: Mendel Rafts: They Don't Matter Supports: Yes Resolution: 0.2 Infill: 20 Post-Printing

Check out this camera gimbal only setup....\nFor more information and to download, go to \nhttps://www.thingiverse.com/thing:2540161\n\nWatch Part 1 here: https://www.youtube.com/watch?v=FkElyRgdvtI\nWatch Part 2 now:...

Runcam3 Protector Camera should be inserted from the top USB connector is accessible Best printed in TPU or other flexible materials Print Settings Printer Brand: Wanhao Printer: Wanhao Duplicator i3 V2 Rafts: No Supports: Yes Resolution: 0.2 Infill:...

Remixing Markqv's mount to reflect the distinct variations between the two models, 2 and 2S. The PDB is positioned slightly higher to allow it to be partially buried within the nose section while still maintaining access to both the SD card and USB...

... frame attachment for mounting a forward-facing FPV camera like the Run Cam. ... Print Settings: Printer Brand: LulzBot Printer: TAZ 5 Rafts: No Supports: No Resolution: .2 Infill: 20% Notes: Print sitting on the front. ... ABS: Extruder/Bed: 240/110

... download, please visit www.thingiverse.com/thing:2540161. Part 1 of this project can be found at www.youtube.com/watch?v=FkElyRgdvtI. Part 2 is located at www.youtube.com/watch?v=bHbfp6JCPTM. ... You can also support me at www.patreon.com/mwilmar.

http://www.thingiverse.com/apps/customizer/run?thing_id=1015101 Instructions Using the following options: rear_cc = 42.5 velcro_height = 2.7 screw_head_size = 9 edge_margin = 3.8 hole_size = 4.6 front_rear_cc = 50 base_thickness = 1.9 solid_wedge =...

Standard mounting screws with a diameter of 2.5mm to 3mm are recommended, as they fit perfectly into the side holes with a 2mm diameter. M2.5mm bolts can also be used as an alternative. ...When fastening the camera board to the bracket, 1.8mm or smaller...

I use TurnigyTM TGY D1290P high-speed micro servos, weighing 2.9g and providing .07 seconds of speed with a torque rating of .35kg, which can be purchased from hobbyking.com. ... I also utilize TurnigyTM T541 BBD high-torque DS nano servos, weighing...

FlexRC Pico X mount for Runcam Swift Micro designed specifically for use with carbon prop protector in mind. I printed it with 100% infill using Nylon, which has proven to be a sturdy material. When mounting, insert nylon screws from bottom up.

This clever design serves as a snug protective shield for the Runcam Micro Swift lens. It perfectly complements the popular holder (https://www.thingiverse.com/thing:2362392) and any other holder with a 24mm distance. ...To secure the two parts to the...

... ...The frame didn't fit perfectly, requiring me to install the FC upside down to connect the motors. To accommodate this, I crafted a small mount for my RunCam Micro Swift camera. ...The camera mount aligns with three screws that hold the FC in place.

... be pretty, but it works. Printed in Nylon with a 0.4 nozzle and 0.2 layer height at 30% infill - still struggling with corner lift using nylon, but everything fits perfectly except for my pod legs, which become bent. ... Let me know what you think!

really compact FPV stand and holder for 2 9g servos and the runcam hybrid

This is a custom Runcam Swift Micro camera mount designed specifically for the Hyperlite Floss v1. Crafted from high-quality TPU with 100% infill, this mount provides exceptional durability and stability. Unlike other Floss swift micro mounts that I...

For the Runcam Micro Swift mounted on the FlexRC mini Owl, I designed a custom mount that provides a snug fit without obstructing propellers. However, its forward projection makes it susceptible to damage. To safeguard against frontal impacts, I...

This Mount Fits Runcam Micro Swift 3 into TBS Source One Freestyle Quadcopter Drone. Scale the Mount Up 1% to Fit Standoffs Easier. Print with TPU Without Supports. Use a Brim to Keep it Upright During Printing. Change Filaments While Printing for...

Cameras supported: Foxeer Racer Runcam Phoenix Mini Runcam Swift 2. - Classic - Longest to compensate the CG in case to use a lipo tattu 2300mah 4s File: Nano Drak Nose Support required 4 nuts and 4 screws 3m (3 metric), This part is glued in...

Universal runcam thumb mount

Runcam Thumb Camera Mount

This is a holder for the Runcam 5, to be mounted using a GoPro-like 2/3-finger-mount.