runcam split 4 3d models

https://www.thingiverse.com/thing:2447154 I needed an adapter to hold the PCB for the Runcam Split and fit on my Holybro 180 Pro, so I designed a custom insert to go between the quad and the battery to hold the Runcam Split's PCB. The insert fits...

After conducting an initial test with the first version of this holder, I discovered that the sides were visible in the Runcam Split's field of view. Undeterred by this setback, I swiftly uploaded an updated design to prevent this issue from...

I customized the Part's design to perfectly work with the Runcam Split HD/FPV Camera AIO. Cut out a piece of the top plate as much as needed to clear the camera's view completely, and I added some ziptie points in the back for mounting my XT60 or...

This mount is specifically designed to hold the Runcam Split Mini in place, allowing it to be securely fastened to the top plate of a Helifar X140 Pro drone. So far, results have been positive, with no issues encountered during testing despite...

Armattan Chameleon mount for Runcam Split. Default camera angle is set at 35 degrees, although this can be adjusted as seen in images one and two. To access the side plate, it must first be removed, necessitating the use of washers. Utilizing...

I'm excited to share my latest ZMR250 Runcam Split v2 camera mount iteration with you, the third one I've created so far! To give it extra shock absorption and durability, I printed this one out of TPU material. Below are the print settings I used.

I crafted a custom piggyback to support my Runcam Split atop my QAVX. I've successfully run it as my primary camera, but it's been quite challenging. I aimed to set it up like a GoPro Session, placing all electronics on top. You can install a...

This mount enables you to install the Runcam Split 2 camera on the ImpulseRC Reverb frame without obstructing a single frame component. I strongly advise printing this file using any rigid filament, such as PETG or PLA, as opposed to flexible...

Housing designed specifically for the Runcam Split 2S, perfectly fitting my TBS Caipirinha 2. The design was inspired by /u/petronioaznar's concept, but I had to create a new one due to only having access to the smaller Split 2S model. It fit snugly...

This design is currently known to fit with: - Runcam Split V2 - Runcam Split V1 (Requires a few winds of insulation tape as it's slightly smaller than the V2) Check out my other designs to find variants for other cameras. All you have to do is pry...

RunCam Split 2S and 3 Micro Camera, paired with VTX mounts, offers versatility for drone enthusiasts. Available in 20x20 and 30.5x30.5 hole spacings, this setup caters to a wide range of users. Specifically designed to work seamlessly with the RDQ...

- Support pour Runcam Split 3 Nano style GoPro Hero session (! Taille différente !). - Montage simple avec Vis M2, avant l'assemblage des composants visser un premier coup afin de bien faire les taraudages (Cela peut forcer). Après l'installation...

This is a case for the RunCam Split, with 25 degrees of uptilt. The top cover houses the camera and can be effortlessly detached from the base. Camera and cover will weigh approximately 40 to 45 grams depending on your settings. Update: Wall...

A canopy for fitting the Runcam Split 3 Nano/Whoop edition to a toothpinck build. Screw will need to come up through the base frame, through the FC and screw into the provided holes. Nano lenses will fit, the wider one is a lil tight. Apply heat...

This mount is designed to hold my Runcam Mini Split perfectly on an ET115 whoop frame made by KingKong (LDARC), and its versatility allows it to fit any 20x20mm stack. The camera can be adjusted at a range of angles between 10 and 35 degrees for...

With this mod you can fit a Runcam Split FPV camera into the Armattan Chameleon frame instead of a dedicated FPV cam. This way there's no need for a separate HD cam, making the whole build lighter and the camera is far enough up front to (almost) not...

This new version includes built-in 3mm spacers to eliminate four of the 3mm tall brass standoffs that come with the split, allowing you to run a longer screw straight through from the top of the vtx mount to the middle brass standoff in the split...

32x52 mm hole spacing. ... TO mount the DVR board and the Runcam. ... fits 5mm standoffs

I printed an adapter for a friend to use in their Strix Goblin, as they were struggling to access the USB port and Micro SD card slot on the RunCam Split V2 board. Mounting the board required accessing the buttons, which was a bit of a pain due to...

________________________ This is a basic 30° Mount designed for the Shrieker to work seamlessly with a Runcam Split or Mini. The goal was to position the camera as high up as possible, minimizing visible propellers in the image. Use M2x3mm screws...

45° 35° 30° 25° Have fun ----------- The RunCam Split 2 sounds like an amazing piece of kit on paper..... - FPV and HD Camera all in one - Wide dynamic range camera - Records at 1080 60fps - Lightweight - No need for a GoPro What's not to like??...

The RunCam Split is the only camera I think will work without significantly affecting the flight characteristics of the quad (CG) - its wider design allows airflow to reach the board. To install the camera, you'll need to cut a small channel on the...

The New SXQ5 Frame (Stretched X) Aero Pod This pod is designed to use the AXii UFL Antenna and Runcam Split / Runcam Mini FPV Cam. Designed by QuadFramesUK https://goo.gl/WSsusq Frame & Pods are Available to purchase from T9 Hobbysport ...

This collection of parts makes it easy to mount a RunCam Split Mini neatly into the nose of a NanoTalon, giving you the ability to tilt the camera. It includes two cutting guide pieces so that you can get a perfect fit. The camera is attached (using...

This is a custom mount I created for my Runcam Split camera that brings the lens forward and up, effectively reducing visible prop interference in high-definition footage. Depending on the frame rate and camera angle, some props may still be visible....

I have designed this block to get the 1 axis gimbal using the RunCam Split 2 camera and 9gr Tower Pro Servo. It works really nice, giving the ability to see not only what is in front of the model, but also what is below. It covers completely the...

I've designed this block to harness the RunCam Split 2 camera and 9gr Tower Pro Servo for a single-axis gimbal system. The result is seamless, offering a 360-degree view that includes what's below the model as well as in front of it. This feature is...

Small brackets designed specifically for the Runcam Swift camera are now integrated into the original mounting system of the Armattan Chameleon drone.

Mount for Runcam Split v4. ...Maid mainly for larger rockets but can be adapted to many uses.

Quadcopter RunCam SplitMini: https://goo.gl/6HSrcy Gimbal motors RCX H1806: https://goo.gl/M2aZ73 Controllers HMBGC V2.2: https://goo.gl/9Cg1r8 Test video from 7-inch quadcopter: https://goo.gl/vLcNZT