runcam split 4 3d models

Hey pilots! ... Check out this easy-to-make bracket that securely holds your RunCam Split mini or Caddx Turtle cam in place. ...Now, get out there and start enjoying those thrilling flights!

It removes the need for 4 screws to hold the mount and frees some space to move battery forward or put on a bigger battery. The front matches good but the rear edges overlap alittle which helps protect the frame a little. Yes it has the name of...

With the clever design of the Runcam Swift mounting system in mind, I crafted a custom plate that leverages both the pivot point and locking screw, giving you complete control over the angle to suit your precise needs.\nPrint two at 100% infill for...

This is a fun project that involves the cheapest Chinese-made two-axis gimbal and one of the least expensive split HD cameras for racing drones, specifically the Runcam Split 2. It works well, but don't expect footage comparable to that of a Mavic 2....

I run Cam 5 and join session 4 out of 5, mounting my 33-degree setup for Iflight's Nazgul.

My other GepRC original mark 4 designs: DJI conversion: https://www.thingiverse.com/thing:4780070 JHE42B buzzer bracket: https://www.thingiverse.com/thing:4720369 GepRC Mark 4 arm: https://www.thingiverse.com/thing:4845447 Not mine, but usefull GPS...

I wanted a holotape with good detail. The original print was awesome but only had the detail on one side. I scaled down the size of the original print to 85%. ...Attach both to make the holotape.

Print two of these, and two pcb-din-clip from voron-2.4 stls Split DIN bracket for printing out from a smaller printer

Sirius Black wand (split into 4 parts)Sirius Black's Wand From Harry Potter (https://www.thingiverse.com/thing:1609837)

This is a combination and a remix of two items: https://www.thingiverse.com/thing:3560176/files - Stand - Inserted HP Logo https://www.thingiverse.com/thing:3187683/files - Wand - splitted the wand in 4 parts

Ive split the part 3&4 stl into two printable pieces. ...Please note, ive not printed these yet myself but they load perfectly in Cura and will fit an ender 3

Split, reusable plant pot for garden starts.

... for 60% ANSI Pok3r. ...the plate is split into 4 parts for easier print and also for better customizations. The STL can be printed on a 18×18×18 cm ( 7"×7"×7") Bed. The plate is also designed with pegs for better support. ...https://3rdeyelabs.io/

... for 60% ANSI Pok3r. ...the plate is split into 4 parts for easier print and also for better customizations. The STL can be printed on a 18×18×18 cm ( 7"×7"×7") Bed. The plate is also designed with pegs for better support. ...https://3rdeyelabs.io/

3D Printer Base v3.4 has been successfully split into two parts, making it easier to print on smaller beds. As this project is still a work in progress, I have not yet had the opportunity to print it out. ... To make assembly smoother, I've added a...

Remix of Super_Satchmo Token Trays for marvel united with a 2-way or 4-way split to hold multiple token types in 1 tray. This is my first remix on tinkercad but it got the job done for me. ... There is a thin-walled version for each which gives more...

The rear wing has been split so it can be printed on smaller print beds (Ender 3) Also added some washers to improve the look of the bolt holding the wing on. ... Wing and body mount has been improved, extending the body mount for the Extended skull...

... factor by a couple of percent. If it's too tight, simply reduce your extrusion factor. This "Y" Split design is actually a variation of my previous design for an "S" bend for one half inch conduit: https://www.thingiverse.com/thing:2958303

I couldn't find a split version that didn't alter other parts of the model and looked robust enough, so I created my own. THIS MODEL HAS NOT BEEN PRINTED YET! PRINT AT YOUR OWN RISK. DON'T BLAME ME IF YOU WASTE YOUR PLASTIC! I'm sure you'll have to...

This is a remix of the Isle of Cats - Scorepad 4 Players.stl from Stinkfoot71. My print area is only 220mm x 220mm so I needed to break it up into smaller chunks. Should be good to print one of each Part 1-4. There's even a bit of an outline on...

Mounting hardware is designed specifically for 3-inch builds, allowing users to securely attach their camera and DVR board to the top of the carbon fibre frame panel. ...Held firmly in place by a combination of screws and 3M mounting tape, this setup...

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/39PMEfJgyHN

Camera is moved back a bit, secured with screws or glue according to your preference. M2 nylon screws and separators are used in this setup. Watch the full tutorial on YouTube: 07shHX5XkHA. To protect the camera, you can use a protective casing...

Built this design to tackle jello from the factory hard-mount issues. Use foam tape on top and bottom sections - it's a straightforward solution. There are two versions available: 1. With tabs that safeguard the carriage from ejection during a...

The Martian II TPU Mount is designed to fit seamlessly onto your existing 3D printer setup. This innovative accessory can be found on Thingiverse, a popular online platform for sharing and discovering 3D printing models. ...Simply head over to...

I designed a custom part using OpenSCAD since no existing option matched the requirements, making it my first personal creation and hoping you'll appreciate its unique qualities!

Hi! Here is a mobula 6 HD lightweight canopy, roughly inspired by the Slim Whoop Camera Mount (Adjustable Angle) by MrShutterBug. ... You'll have to remove the open square shaped part on the camera and re-use its two screws to avoid camera rotation.

This is a brand new take on that thing from Thingiverse: 2824974. It's almost identical in design but now the case for the board is built into its base. Check out this video to get an idea of what I'm talking about: RH3p1bRIGXM on YouTube. ... For the...

Printed without supports. This model fits 30mm M3 standoffs perfectly. The antenna holder is specifically designed for FlySky's iA6B receiver antenna. FPV enthusiasts can enjoy a 15-degree angle, but you're free to modify the source file if you'd...