runcam night eagle 2 pro sensors 3d models
964852 3d models found related to runcam night eagle 2 pro sensors.thingiverse
Martian II Side Plates for the RunCam Eagle 2 and Eagle 2 Pro. The camera features a 0-45deg mount. To assemble, you will need qty 6 2mm x 4mm screws; the camera should come with 4 that fit directly. I found some 2mm x 6mm screws from previous RunCam...
thingiverse
The standard bakplate provided with the Martian 2 frame fails to fit the RunCam Eagle 2 due to its two connectors. Alternative designs I discovered were flimsy, unable to keep the RunCam stable. ... This design stands out for its sturdiness, ensuring...
grabcad
The RunCam Eagle 2 FPV camera boasts a 1/1.8" CMOS sensor with an 800TVL horizontal resolution, offering a choice of 2.1mm or 2.5mm lenses and switchable NTSC/PAL signal systems via the OSD menu. It features internal synchronization, an OSD set, and...
grabcad
This printable adapter is perfect for connecting the Runcam Night Eagle 2 pro, and possibly other models, to a C/CS mount lens with ease. Simply screw in or push in an adapter ring onto the part, and you'll have multiple flange/attachment options...
thingiverse
The Runcam Night Eagle Telescope Eyepiece Adaptor is designed specifically for use with telescopes and the Runcam camera system. It allows you to utilize your Runcam camera while navigating through the night sky with ease. ...Simply attach this adaptor...
thingiverse
Based on the detailed spec sheet provided by RunCam, I've carefully crafted this design, even though it wasn't my original creation. While it may not be flawless, rest assured that it will function as intended. A close examination of the holes...
thingiverse
This mount is tailor-made for the Runcam Eagle 2 Pro FPV camera, which comes equipped with a 16mm diameter front lens and a wide camera housing. It's installed directly in the nose of the MTD - My Twin Dream, as seen in the attached pictures. I've...
thingiverse
I needed to shield my big eagle camera from the elements, so I created a fresh batch of side plates and camera cage to give it superior protection.
thingiverse
Runcam Eagle 2 pod mount. Fits similar full sized Runcams 28 x 26.5mm . Can be mounted on the side of the plane. ...Takes two 3mm screws
thingiverse
Camera Lens Shield for Runcam Eagle 2 Made with Precision Infill at 0.3mm Layer Height, TPU Material If You're Searching for Camera Lens Protection for the Micro Eagle, Check Out This Model https://www.thingiverse.com/thing:2884652
thingiverse
This is a revised version of https://www.thingiverse.com/thing:2577387.\r\nThe camera cage has been modified to accommodate a Runcam Eagle V1 instead of a Swift 2, and I've also integrated holders for the VTX and RX antennas.\r\nTo complete this...
thingiverse
This is a RunCam Micro Eagle mount specifically designed for the Martian II 220 mm system. To assemble the mount, use the original screws provided to secure the camera at the desired angle. ...Next, import the mount into your preferred slicer software,...
thingiverse
Just my design of a eagle 2 camera protector for my armattan rooster 6 inch. ...Super Simple.
cults3d
Just my design of a eagle 2 camera protector for my armattan rooster 6 inch. ...Super Simple.
thingiverse
However, considering the considerable stack height of components such as the RaceFlightOne Revolt, Bolt, TBS Unify Pro, and Whitenoise PCB, using these standoffs is practically mandatory. *Update: The v2 revision should allow for the m2x4mm screws...
thingiverse
I'm planning to install a Runcam Micro Sparrow on my GT-M5 with a 2.1 lens, so I've designed a custom cover/protector that shields the lens from damage in case of a crash while keeping the FPV experience intact. ...The protector will be printed using...
thingiverse
Simple mount for Runcam thumb 4k. I pushed it far forward to fit a bigger battery. I am using a 1500mah 4s. ...Will add some more angles later.
thingiverse
I Design Custom Lens Caps for My Quad Cameras by 3D Printing Them in Flexible Rubber Material. ...The Unique Texture Adds Protection and Allows Me to Personalize Each Cap with a Distinctive Sunken Logo Using a Permanent Marker.
thingiverse
I designed this FPV Camera Mount specifically for use with the RunCAM Micro Eagle and E-Flite Radian Pro Glider. Its unique design allows you to mount the camera on the tail of the glider, providing an unparalleled view of your plane in flight. By...
thingiverse
... will leave spectators breathless. Whether you're flying over vast expanses of Martian terrain or navigating through narrow canyons, the Runcam Eagle 2 FPV Camera Mount for Martian 2 is the ultimate tool for capturing breathtaking aerial footage.
thingiverse
This TPU mount is compatible with the Armattan Tadpole 2.5 inch build, specifically designed to house the Runcam Night Eagle Pro 2 camera. The rear was engineered for angular adjustment of the top plate, allowing the props to clear the camera while...
thingiverse
I built a mount for the Runcam Eagle 2 and the Readymade RC 1.2 Ghz VTX, minus its case, with a heat sink added, specifically for my FT explorer. ...Although it's possible few individuals run this setup, I decided to upload it regardless.
thingiverse
This design is currently compatible with: - Runcam Eagle 2 (full size) - Runcam Owl 2 Check out my other creations for variations on different cameras. As indicated by the name, you don't need to screw the camera into the mount. Simply pry it open...
thingiverse
Here is a fpv camera mount that I designed specifically for the RunCam Eagle 2 and it securely attaches to the top and bottom plates of the frame using slots on the plates that align with tabs. The camera mount is engineered to hold the camera at a...
thingiverse
https://www.thingiverse.com/thing:4539843 Low Drag FPV Nose for Multiplex Funjet Ultra 2 Designed to Fit the Runcam Micro Eagle FPV Camera. This nose also fits the regular Funjet 2 and the old Funjet and Funjet Ultra! Cutting the nose off a funjet...
thingiverse
Depending on your printer it may not fit the Runcam Thumb Pro. In that case, some sanding will be required. It fit for me, so can't guarantee fitting after sanding. You can see some stringing in the pictures. Depending on your preset there might be...
thingiverse
Dummy for the Runcam Micro Eagle: overall build dimensions closely resemble those needed for functional testing, with only the most notable distinction being the larger lens size compared to the Micro Swift.
thingiverse
A custom-made adapter plate is designed to relocate the mounting point of the Runcam Eagle camera on the ZMR250 quadcopter frame, shifting it further back towards the rear support pillars.