run cam 2 3d models

CAM 3D SOLIDWORKS

This is a 3D printed cover designed to shield the Wyze Cam V.2 from the elements. It's not explicitly stated whether this protective casing would also be suitable for the Wyze Pan model. The two available designs feature either a flat or pointed...

nose for mini drak, enjoy. ...will possibly fit other mini cams

Just a quick remix for mounting an Action2 cam to the QAVS frame

The lever's eccentric cam surface offers secure attachment through an over-center mechanism that applies pressure to prevent slippage. Moreover, three seat track mounting options are available on both wide and narrow sides of the handrail. ...The entire...

UPDATE: Version 2.0 is here: https://www.printables.com/model/382003-ender-2-pro-sd-card-adapter-and-wyzecam-v3-mount-v This is a mount I designed to add a Wyze Cam V3 to the Ender 2 Pro. There aren't very many good mount points on the printer...

... tweaked the cam to include a thumb notch for releasing the line. The sides are made from 3mm perspex, while the cam and cam plate are crafted from 6mm material. ...To secure everything in place, I'm using 3x15mm bolts paired with nylon lock nuts.

Thick cam mount for the kayoudur Just print it in tpu The standoffs are in the FOV

Hole Pattern Key: A-Mount to Phantom 2 body 4 screws-pads for standoff B-45mm X45mm and 45mm X 25mm hole pattern for controller boards 6 holes C-2 holes for static cam bracket D-holes for gimbal bracket arm to roll motor E-rubber anti-jello mounts 2...

First pass at automata CAM

[Warning, if you downloaded this in the first hour of publishing, abort; some Tinkercad exports were bad.] The Hawkwye Firefly Micro Cam 2 was released, but the included hard-mount causes mega-jello. The Micro 2's rolling shutter is highly...

After reprinting it, I discovered that the original design wouldn't fit my BIBO 2 printer because it was too thick in front and blocked the rear vent, and also too thick at the back where the Z-Stop switch was located. Since moving the switch wasn't...

ESP32-CAM Case Type A - The camera position is centered. ... Donate: https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=RDN7ZGAVFS5UE

I made a cam program with solidcam. I uploaded all part link below . ...If you have any question , please contact with me.

Ein kombinierter Halter für den " RF-V16Tracker " und meiner 360 Grad Cam in einem Stück für meinen Zubehörhalter https://www.thingiverse.com/thing:4691566

The bosses against the Phantom body allow insertion and removal of the anti-jello rubber mounts, and will allow a contoller board to be mounted from the top plate. The plates can accommodate a static mount or a gimbal mount. Hole Pattern Key: A-Mount...

For this reason, you'll probably want to hotglue a +2.0 reading glass lens over the front of the module to get it back in the region of 20-25cm, where the camera actually sits from the center of the build plate. To assemble the pi, you will need a...

Hole Pattern Key: A: Mounts 4 screws onto the Phantom 2 body, using pads for stand-offs B: Includes 6 holes in 45mm x 45mm and 45mm x 25mm patterns for control boards C: Supports a static cam bracket with 2 dedicated holes D: Offers space for gimbal...

This project is a modular harness that will attach and support the Pi and the camera module to the front or side of an Ultimaker 2. The camera can be moved into any position and rotated so it can look down on your print, hang underneath looking...

this is a model of cam

To complete the assembly, you will need the other components of the arm, specifically the pi_cam_head_v2, at least one pi_cam_arm_v2, and two bolts - the large bolt works perfectly fine. ...As shown in my images, I used a base, two arms, three bolts...

I built remixed a Raspberry Pi Cam shroud to have a glare protector on it, unfortunately the standard tool couldn't get down to the lens to adjust. ...This bit fits my shroud, and also can be used with a screwdriver.

Simple moveable webcam holder, designed for Wyzecam but can fit Logitec, Pi Cam etc if adapted - STEP files are included. ... I made this just so i can move the camera around, and use it in my Tukkari enclosure Ajustable height, requires 3x 3mm...

universal mount for source 2

cam for tool changer CUT-40 CTM collombo filipetti

*** I wanted a quick and easy way to slap a pi cam on one of my printers. After a couple of revisions this little mount is good to go. The mounting tabs are MMS compliant, and the box interior is sized for an easy fit. No supports...

I crafted a custom protector for the quadcopter's cam that met my needs perfectly after ditching the previous designs. Since I required more flexibility, I redesigned it entirely and made it fully parametrizable, allowing users like you to customize...

The Chinese-made Xiaomi Yi camera is being held securely in place by a handmade cam holder. The user has selected their printing settings to bring this object to life, starting with the printer itself. A choice of printer type can be made here, but...

The Handler for Cyclope 2 Camera is Connected to E-011, Activating.

This will fit cameras like the runcam nano 3 MCK edition or foxeer toothless 2