rufus from kim possible 3d models

supports R1 SP-SA Profile)6.25U Spacebars w/ a Centered Stem & max height of 13.60 mm Print SettingsInfill: 15-20% GyroidPerimeters: 2-3Layer height: 0.2mmSeam: Rear or Near (check the preview in your slicer to see what looks...

I'll just explain how to properly fill and drain the tank and how to agitate.FillingRemove the cap from the lid (DO NOT REMOVE THE LID ONCE THE FILM IS INSIDE), rotate the lid so that the arrow is pointing the drainage port on the side of the...

- 3D Printer - [SAFilament Red PLA](https://www.diyelectronics.co.za/store/pla/3307-sa-filament-pla-filament-175mm-1kg-red.html), [eSUN Cold White...

If it causes copyright issues, i will remove it. Remixed from: https://www.thingiverse.com/thing:4248444 https://www.thingiverse.com/thing:4614658 https://www.thingiverse.com/thing:2506910 https://www.thingiverse.com/thing:3853037...

I used 3mm diam screws with 5mm diam head in pictureCards can slide in & out from the top. Changing/swap card easilySatisfying fitOptimized for 0.6 nozzle printingNo supportMade for my kid as a companion for:...

Update - 29/09/2020I have removed the 3D printable stand from download as keeping the clock at that high an angle does effect the sand and the strength of the movement. I will design another stand with a lower angle and see how well the clock copes.

The relay bodies and caps were remixed from myyellowminicooper's designs here: https://www.thingiverse.com/thing:4303759 Thanks to myyellowminicooper! Those designs were a great starting point for me. I made adjustments to the relay body, relay...

It is easiest if you start with the chain hanging down from the handle. Start spinning slowly, and then start to vary speed, and even reverse the direction. Speed changes should be gentle, because abrupt changes will cause the chain to jam and fly...

All original models are from UntangleWORKS (https://www.printables.com/@UntangleWORKS). ...All I did was scale down the model and change the grip to fit DUMMY 13 (soozafone)(...

This is a fun project I've made for my wife, not for the obvious reasons, but can be used for many situations ;) Since the pandemic and with the need to work from home a totally new house routine started. Not only we need to live together, but...

The only one that does not fit is the Tower Cooler2 x 5V 40x40x10 mm fan12V 1.5A Power Adapter (Surely you will have one at home to collect dust).5pz M3x10mm countersunk screw6pz M3x16mm countersunk screwSome wires and dupont female connectorOne...

The following example of a simple code to get you started: ```Python # Python code to create G-code with specific parameters and tool settings import math # Tool settings (parameters should be adjusted according to actual tools used) tool_diameter =...

You loose some of its capabalities and strenght but you save on filament and printing time.(I suggest you try them and chose the one that suit you the most…all are equally compatible with all the terrain tiles…except the last one of...

 If I made him exactly in proportion, the parts would have been too small.4 - When removing parts from the printer bed, it's a **VERY** good idea to place left/right parts into separate containers to help with the assembly process...Assembly...

What To Do Have one person from each pair (or group of 3) choose an ugly fruit for their creation Hand out one set of VeggieMake parts to each pair (or group of 3) and ask them to start making creatures. They will quickly determine that they can’t...

Don't try to print the Panel lying flat, it will make the part unusable because the dovetail dimensions will be inaccurate and you won't be able to fit the parts together.No brim required for the rest of the parts.Bolts & Nuts should be printed with...

Base: I used some 2x4mm magnets that were left over from the MakerRx kit to hold the Base Cover to the Base. The Base can be printed without supports. I manually added a small support for the cord slot inside the Base. After printing, just pop it...

 The air flow direction should be pulling air from inside the enclosure to outside.Place the second TPU_Fan_Gasket_X2 on top of the fan.*Place the PETG_Fan_Exhaust_Adapter_Bracket_X1 on top of the TPU_Fan_Gasket_X2.Insert the screws that came...

I used small jewelers files and plenty of patience to perform this step.Assemble the Staircase.To assemble the staircase, I performed the following steps:• Slid "Staircase.stl" up through the bottom of "Base.stl", pressing it upward until the...

It is a remix of the original spoolholder that uses printed roller arms and springs to press the spool down.To improve the stability of the arm, the profile was divided into two halves, the lower one containing the bushing and separated by a gap of...

ESP32 DevKitC (v1 or v4 tested)...

There is also a strap hole, so you can use it immediately by lowering it from your neck. The device supports capacitive touch panel operation. Pass a 0.5mm steel wire through the hole at the tip and through the edge of the hole to the strap hole. If...

Compatible with Smart Diffusers extension.Example of parameters from one family: Type CRL-400-R CRL-160-R CRL-315-R Air Flow 0.00 L/s 0.00 L/s 0.00 L/s Arrow 300.0 300.0 300.0 Arrow Distance 0.0 0.0 0.0 Arrow Length 50.0 50.0 50.0 Arrow Visible True...

After printing one of them, he struggled to align the parts and stick them together with glue, and not only but it broke shortly after. Seeing him cry after two days of work (it's not easy to be a kid, you know..) made me want to help him.Easy...

This is a mechanical dispenser for example for fetilizer but you can put in this whatever you want.  things you need apart from the printed parts :-2x  M3x20 screws (you can find these in the spare bag if you have a Prusa)-2x...

The other issue is that there are two Y-Values for the X-Values where the asymptotes should be, but this is another thing I had to compromise due to space issues.) Print instructionsPDF Version of Instructions Images...

   Don't forget when you are doing this to think about the position of the enclosure and make an allowance for the IEC plug that will come from underneath the case.At this point you should be ready to fit your case.  Good...

This will prevent the sides of the wing from contacting the case. (4) Insert switches and keycaps into plate and PCB. (5) Clip the gasket wings onto the plate (not the PCB) at the positions indicated at Figure 2 in the photos above. (In Figure...

oil) on it.attach brackets on all 4 corners to hold the base plate (height from floor to underside of the board ~ 44cm).attach with a bracket the base plate to the wall. (not mendatory, but I recommend that because it brings lots of stability)Put...

This helmet can support the following: - A suite of Picatinny rail compatible side attachments from Halo: Infinite and Halo: Reach - A flat, universal overhead mounting plate - Multiple UA attachment upgrades - A suite of legacy ODST attachments -...