rubbermaid shed door latch 3d models

This is a direct replacement with a vintage-style Rubbermaid Shed Latch that I managed to break off by accident. ...It's engineered to snap snugly into place on the shed door, just like the authentic version.

A replacement latch for my RubberMaid shed, which was inherited from an unknown source, has been installed. The original part featured a hole designed for securing with a padlock but I opted to remove it since locking is not required and I don't...

I'm using an old RubberMaid shed, and all I know about it is that someone gave it to me. The original latch had a hole for a padlock, but since I don't need one, I left it out - besides, I doubt anyone could break in with a basic plastic latch like...

I'm fed up with both of our Rubbermaid sheds' latches being torn apart by monsters, but rather than letting my frustration get the best of me, I chose to channel that energy into something positive.

This is a direct replacement with an older Rubbermaid Shed Latch that I happened to snap off accidentally. It's designed to snap fit securely into the shed door like the original. Print Settings Printer Brand: Wanhao Printer: Wanhao Duplicator i3...

Printing vertical will make the part weak. Print in PETG as it will be outdoors Resolution: 0.2 Supports: Yes Compatibility This seems like a very common latch on Rubbermaid products. Look at photo to check if it will fit. The official part number...

A replacement latch is available for the Rubbermaid Big Max shed, identified by part number HIP-046H. ...This new component was designed using the CAD software Fusion 360.

Threaded Hinge Pin to replace a broken door pin on a Rubbermaid "Big Max Compact Vertical Storage Shed" Had a few of these parts on storage sheds break. Unable to find any replacement parts so turned to a 3d Printer. ...

My Rubbermaid Jumbo Storage Shed (52 x 30 x 82" H-1229) door handle shed broke off near the 4 holding screws. I designed this replacement in Rhino and it works better than the original as it is reinforced. I reduced the length to make (without...

My Rubbermaid Jumbo Storage Shed (52 x 30 x 82" H-1229) door handle shed broke off near the 4 holding screws. I designed this replacement in Rhino and it works better than the original as it is reinforced. I reduced the length to make (without...

Created this to repair a broken shed door. ... Printed on both Prusa and Voron in PETG and ABS.

For latch itself, I used a piece of wood ( 20mm x 20mm x 300mm ), held by 6mm furniture screw.To hold latch in upper position I used magnet ( diameter 10mm ; height 2mm) in printed magnet holder.Printed using Prusament PETG on my Prusa Mini+ - no...

wall anchor for rubbermaid shed

Rubbermaid Shed Shelf Bracket. Enjoy! ...

This latch connects directly to the handle found within the Lifetime storage shed's interior. ...On my particular model, attempting to open the shed results in the latch failing to elevate the lock's engagement height sufficiently.

Just a simple hook for your Rubbermaid shed walls. ... <a href="https://www.buymeacoffee.com/mekpong" target="_blank"><img src="https://cdn.buymeacoffee.com/buttons/v2/default-yellow.png" alt="Buy Me A Coffee" style="height: 60px !important;width:...

I bought a Rubbermaid vertical shed model #1967673, originally sold at home depot. I got it from an auction and found that it was missing the wall connectors. They are these clip type brackets that hold the walls together at the center seams. ...

Now it prints pretty good in PETG.100% infill, recommend PETG for strength and UV resistance, but PLA might work with eventual sun degredation, 0.2 Structural, MK4 (or others), 0.4 nozzle.These shed parts broke so easily so good to have replacements...

works in my Big Max Shed

Recently picked up a Rubbermaid "Big Max" shed and found myself in need of additional wall anchors. As a total newcomer to 3D printing, I made an unfortunate purchase - a large roll of clear ABS plastic. Deciding to design and print my own anchors...

Olive/Sandstone Vertical Outdoor Storage Shed (3749) uses the same lock hasp as some of their other models. ...The original design was created with an older version of TurboCAD Pro and features were mostly copied from the original model, then sliced in...

I have a Rubbermaid 7x3 shed for which wall anchors are no longer produced. I found a few variations on here but none was perfect. ...This one fits snugly into the slot for the wall anchor and can optionally be screwed in to the wall.

This latch is designed for Rubbermaid toolboxes from the 80s and 90s, possibly later models as well. Failing to find this part online prompted me to create my own version. To use it effectively, you'll need to drill out the hinge holes to match your...

I designed a latch for old Rubbermaid toolboxes sold in the 80s and 90s, possibly later too. Since I couldn't find the exact part online, I created my own version. To use it, you'll need to drill new holes in the hinge area to fit your specific hinge...

 This is what sits in the wall groove inside the shed. Shed SKUs I think this fits: 2035892, 2119053, 1887156, 1967672, FGSL3000SDONX, 1967673, FGSL2000SDONX, 1967660, FGSL1000SDONX, 2035891, 2035897, 2035894, FG3747SWOLVSS, FG375301OLVSS,...

When the lid latch on my 30-year-old toolbox broke, I designed this replacement.Should be printed with the flat edge face on the bed.  Supports are necessary in this orientation but affected surfaces aren't visible.  Being a functional print, I...

This is the latch portion of old Rubbermaid toolboxes from the 80s and 90s. I couldn't find the part, so I created one myself. To achieve greater strength, use 100% infill. Pilot holes are included in the model, but you will need to drill them out...

A prototype of a shed entrance was made specifically to create a door restrainer and fastener, designed for an individual unable to stoop.

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/7JttOND61ei

Door latch for double doors