rpi4 heatsink case 3d models

This design enables you to attach any 92mm case fan to an Intel heatsink. At least specifically those from the Pentium 4 era, which is what I'm using in the example.   Some Assembly required. I used 4x M4 nuts, and M4X30mm screws to connect a fan...

A case for raspberry pi zero 2 with quick micro-sd card access and good cooling options. You can fit up to an 8mm high heatsink and if necessary, you can attach a side blow fan. For assembly you will need: 1 Bottom half 1 Top half 1 Raspberry pi...

[Amazon link](https://www.amazon.com/gp/product/B099ZCSJW7/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1) - The case also holds a Pi Zero 2 W by snapping it in place. - You have a choice to print one of 2 snap on lids. One flat or one with a...

This solution provides: - A compact case to hold a native Pi camera, or a $9 equivalent like mine... Amazon link - The case also holds a Pi Zero 2 W by snapping it in place. - You have a choice to print one of 2 snap on lids. One flat or one with...

A 15mm * 10mm * 25mm heatsink.

Heatsink for power IGBT modules.

A model of a heatsink I made from a drawing made on a paper so I can make a 3D model of an amplifier casing for a friend who couldn't quite imagine how his idea would look like. The original was made in SW2009, cleaned up a bit in SW2012. ...I suspect...

I deleted the vents, moved the antenna hole slightly, and added a square hole to accommodate the 22 by 22 by10mm heatsink I wanted to use.

This is a DIN rail mount for the Raspberry Pi 4 that necessitates the Heatsink Case. The most significant issue with the Raspberry Pi 4 to date has been its tendency to become extremely hot immediately after boot-up, especially when applications are...

Remixed from this original design to accommodate a Raspberry Pi with heatsinks, with the roof optimized for a snug fit. Printed using the SD Card side facing downwards on the build plate without any additional supports. ... Note: Use the cap from the...

Remixed from this one (https://www.thingiverse.com/thing:3026059) with the "roof" thinner to allow the fitting of Rpi with heatsinks. Printed with the SD Card side on the bed without supports. ... Note : use the cap from the original thing...

I have remixed this case to be compatible with Pi TV Hat.

Based on scaryPug's design: https://www.thingiverse.com/thing:4572202 I maked some modifications The improvements are: More space for heatsink (added 8 mm) long are dubbel short vantilion holes Same as the original, all parts are friction fit, no...

A 9600GT's heatsink and fan have been detached.

heatsink and metal frame designed in catia v5

... by sinns worked well, but I lost my SD card under the pi board too many times. Added structure to stop SD card from falling inside, and added structure to stop light wash from coming through both holes. Lower case is modified, upper case is not.

Heatsink 14x14x7mmProduct link for Ref: https://www.amazon.de/-/en/CTRICALVER-Aluminium-Heatsink-Adhesive-Printers/dp/B09DKJPZRX?th=1

I bought my aluminium case here: [AliExpress](https://www.aliexpress.com/item/4000506204951.html) Use M4 x 8mm insex screws to connect the case mount to the VESA mount. Use M6 insex screws in the VESA 200 mount. ... I also included the Autodesk...

... loose from cable tension over time. There are small slots provided for the wire. I bought my aluminium case here: AliExpress Use M4 x 8mm insex screws to connect the case mount to the VESA mount. ... I also included the Autodesk Fusion 360 project.

Modified case top and bottom with 5v and ground GPIO pins cuts to power my LED light. Print ListTop (pizero2casebottom)Bottom (pizero2casetop)2 clips (Clip_wire_interlock)Parts Needed 4x M2.5 screws 

I printed out the case and unfortunately it didn't fit or close properly due to a missing cutout for the 4 PoE pins. I kept the original files intact, so you can choose what you prefer. The ones labeled as "with_poe_hole" are the new ones I...

I have remixed this case to be compatible with Pi TV Hat. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.3 Infill: 20 Filament: SUNLU PLA+ White Category: Electronics

I have remixed this case to be compatible with Pi TV Hat. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.3 Infill: 20 Filament: SUNLU PLA+ White Category: Electronics

This is a Megadrive case designed specifically for the Odroid XU4, featuring either a Blue Heat Sink or fan setup. To choose the correct upper part, determine your XU4 version first. The case was printed at 0.1mm layer thickness using PLA material.

Not really a remix as I designed this from scratch, but an alternate lid with mounting holes for a standard 40mm fan. ... It most probably fits the original case (https://www.thingiverse.com/thing:4098207) too, but I haven't printed that to test it.

I Dislike Complex Cases That Never Print Correctly and Don't Fit Properly. So, I Prefer to Keep It Simple. This Design Uses a 3-Point Mounting System Allowing You to Plug the Fan into the 5V / GND Headers on the Raspberry Pi. In My Example, I Use...

I dislike the complex cases which never print well, and never fit well. So I like keeping it simple. This use a 3 point mounting so you can plug the fan into the 5G / GND headers on the raspberry pi. In my example I use a step-up (boost converter)...

• The top case was modified with an Apple logo inset and altered to accommodate the 60mm fan. • The bottom plate was also modified to fit the 60mm fan. • The grill was customized to work with the Raspberry Pi4 and now features: - Ethernet...

I have taken this design from my old computer heatsink in motherboard.

This is a straightforward 40x40x10mm heatsink, designed for numerous applications in diverse projects.