rpi4 gamecube 3d models

This is a wall-mounted GameCube controller holder that comes equipped with a wire hook for easy installation via an adhesive strip. The holder works seamlessly with all official Nintendo GC controllers, as well as every knock-off brand I've tested so...

This is a 3d printable replacement power button for the Nintendo Gamecube. Spice up your 'Cube or give it a bit of flair with a new button. Or just replace one that is broken or missing.&nbsp;</p><p>&nbsp;</p><p>I would advise printing this at .15mm...

The original design for the Gamecube buttons contained inaccuracies compared to the authentic ones. When I attempted to utilize them in my Gamecube controller, they failed to provide the precise feel when pressed. To rectify this issue, I decided to...

I recommend the Noctua 40mmx10mm FLX 12V model: https://amzn.to/2JXbJAe The plate mounts to the stock GameCube fan frame with the original fan screws and then you use standard fan screws (that came with your new fan) to mount your 40mm fan to the...

... over time, the arms will conform to this shape. In contrast, the extended plates do not require this flexibility. When it comes time to print, you'll need to decide between screw or 3M attachments - be sure to print two "GameCube_Mount_Arm" units.

Initial Release of My GameCube Digital Port Plug A Warning: This Part Demands Minute Levels of Detail Printing I had to rely on a professional print company to produce my prototype due to the extremely fine levels required for this part. The Pins I...

A replacement reset button I designed for a GameCube that was missing one, which I'm repairing. Since there's no online information available on replacement GCN parts, I decided to share the file here. Let's update this information. V2 Released. I...

This simple cap is designed to replace worn-out GameCube joystick tips.\nThe rubber section, prone to wear after prolonged use, gets replaced by this cap.\nI've included multiple styles, with my favorite being the neg_ridge model - it feels most...

Recently I obtained a GameCube microphone and the game Odama, but the controller clip wasn't included (and wouldn't fit on my RetroFighters BladeGC anyway).Since I planned on using the mic while streaming the game, I realized it would be a good idea...

Recently I obtained a GameCube microphone and the game Odama, but the controller clip wasn't included (and wouldn't fit on my RetroFighters BladeGC anyway).Since I planned on using the mic while streaming the game, I realized it would be a good idea...

Initial release of my GameCube digital port plug. A word of warning this part requires extremely fine levels of detail printing, I had to have my prototype produced with a print company. The pins I used inside this connector are pulled from a PCI...

... fixed asap. Filament colors used to match the original Gamecube: Silver Cube Filament: https://amzn.to/2Rahv2t Orange Cube Filament: https://amzn.to/38kCSnn Indigo Cube Filament: https://amzn.to/2G50el6 Black Cube Filament: https://amzn.to/2R8dYlp

I was making a USB adapter for Wii DDR pads, and didn't want to wait for GameCube controller sockets (console-side) to come from China so I made my own. The idea is that you superglue some solid-core copper wires in the channels, and then sand the...

This mod uses a custom 3d printed fan mount for the GameCube, which allows you to install a standard 50mm x 10mm PC fan. The mod was created with the intention to use a quieter fan than the original system fan, but it also provides a means to replace...

It was requested by Newschool2k17 and inspired by his mod https://assemblergames.com/threads/gamecube-silent-fan-mod.67463/. The suggested fan is a Noiseblocker XS-1, but any 50mm x 10mm 12vdc fan will be compatible. The noise blocker fan can be...

So, I'm browsing All3DP when I see this Pi-Powered mini Gamecube from @sparrows89 https://www.thingiverse.com/thing:2539417 And I think, "Yeah, that's pretty cool!" and I see that Zelda disc just sitting there on the table, and now I'm furious. I...

This is an adapter plate to allow you to replace the stock custom 50mm fan in the Nintendo Gamecube with a standard 40mm x 10mm thick fan. I chose to use a Noctua 12v fan with it's low noise adapter for quiet operation. I recommend the Noctua...

It's designed to snap into the Digital AV Port on the back of the Gamecube. You must desolder the Digital AV port and install a KNJN Pluto-IIx board. You can purchase one at this link http://www.knjn.com/ShopBoards_RS232_Parallel.html. To make it...

- Optional colour for Gamecube i.e Orange Spice, Indigo, etc. - Adhesive like superglue or hot glue. - Optional "ATI" sticker printed on adhesive backing paper. When printing Body.stl I recommend printing on a glass bed to keep the surface smooth...

- Optional color for Gamecube, such as Orange Spice or Indigo. - Adhesive like superglue or hot glue. - Optional "ATI" sticker printed on adhesive backing paper. When printing Body.stl, it's recommended to print on a glass bed to keep the surface...

This is 2 versions of a Nintendo GameCube eject button one with a dimple and one without, this is NOT A 3D SCAN and not a remix it was built by me from the ground up with measurements taken from an actual GCN button and adjusted for the fit I like to...

Hi !\nThis is my 3D-printed portable Gamecube. It was designed to enable users to play GC games and emulators on the go. Specifications include :\nA 5mm-thick shell (this will need to be changed later, as it caused issues with some ports like the AC...

This RPI4 case addon is usable only with armor case mounted to RPI4. Case is for 40x40x10mm fan. ...I am using Noctua NF-A4x10 5 V PWM fan 4pin direct connected to RPI4.

Badges for the RPi4 remix of the AjSTer case, choose one, print, and glue in place!

Badges for the RPi4 remix of the AjSTer case, choose one, print, and glue in place!

A rail mount extension to the Malolo's RPI4 case that allows mounting a UGreen SSD M.2 Enclosure as in here.

A Peach themed Gamecube stand!

A v1 version of a rack shield for a RPi4 with cooler case, to be mounted in a 2U 19" rack system.Need 4x2.5mm, 20 mm long screwI've used this 19" 2U frame : DAP 2 HE Rackblende f. ...Modulsystem 10 Segmente MP-1</p><p>&nbsp;</p>

This is a housing made for a OpenPlotter installation. ... Based on a RPi4 with PiCAN-M hat and some additional I2C and GPS-modules. All placed inside a box for a clean installation. ... Also a made a place for a 30x30mm cooling fan in one of the sides.

... the entire thing. For reference, on Libreelec, with the fan turned off, my RPi4 reached temperatures of around 66°C. ...However, when I activated the fan, the temperature plummeted to a mere 38°C - as evidenced by the accompanying pictures.