rpi 4 3d models

I really liked the RPI 4 case done by "ArtieH" but wanted it to use a more standard 4010mm fan, and while I was at it-- i replaced the OctoPrint logo with the mainsail logo.

Designed to hold a rPi 4 against the rear plexiglass of the Ender6 by clipping into the rail. ... Provides a couple of choices for camera angle (I prefer the 55 degree version)

Bracket can support both RPI 3B and RPI 4 devices. 1. The 1U rack is a Rising Electronics 1U 19x6 vented cantilever shelf which can be found on amazon for aprox $19 2. The #4-40 flush nuts can be found at c4labs under "Upgrades and add ons"...

Bracket/Clamp for holding my Rpi 4 case to the OTA of a telescope.

My setup: - RPi 4 main board - HifiBerry DAC+ with phone jack - All-in-One controller / V2 - Waveshare 3.5" touch screen The case is designed so that each part prints separately, resulting in a nice and smooth structure on all visible surfaces. I...

I take the lower case a make a cleaner version for the RPi 4

<p>This is a remix of the cover for a RAM heatsink on backside of the Raspberry. ...Printing instructions are the same as the original.I use low profile black RAM heatsink from RPi 4 kit for cooling the RAM.

Remix of https://www.thingiverse.com/thing:2720009 with an update to support an RPi 4 B

Rpi case

rpi case

Customized version of https://www.thingiverse.com/thing:3320287 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3320287

I made this design for a RPi 4. There are other nice similar designs around but I wanted one which protected the edges of the screen. The cover for the Pi4 itself is made as one piece at the cost of having to print with supports. ... As the design is...

I made this design for a RPi 4. ...There are other nice similar designs around but I wanted one which protected the edges of the screen.The cover for the Pi4 itself is made as one piece at the cost of having to print with supports.As the design is made...

RPI zero with serial header box

Instructions and BOM at https://www.instructables.com/id/RPi-Macro-Scope/ Hardware used: 2 x 3/8 plastic screws, McMaster-Carr part number 90380A011 (https://www.mcmaster.com/#90380a011/=1ajevok) 4-40 x 1" bolts, McMaster-Carr part number 92314A115...

... (https://www.mcmaster.com/#92314a115/=1aq7zuf) provide a sturdy foundation for the camera mount. - A knurled 4-40 thumb nut, also sourced from McMaster (https://www.mcmaster.com/#92741a100/=1aq808l), offers a secure grip and easy adjustments.

Hello ! ... This is a Case for Rpi 4 with 40mm fan mount fix this with m3 screws

... an RPi module, IMU unit, camera component, and lidar sensor in a single package. ...The GitHub repository containing the OpenSCAD design file and supporting documentation can be accessed at [here](https://github.com/MomsFriendlyRobotCompany/ins_rpi).

Hello,\nI'm thrilled to share my remix for the Raspberry PI Cam and the Wide Angle Camera.\nThe RPI WWCam can be found here, at these reputable retailers:...

To replicate this, you will need an Rpi, 5mm wood or acrylic, glue or double-sided tape, an LCD from an old laptop without the inverter, an LCD board controller, a 12v 3a adapter, and a DC-DC step down converter to convert 12v to 5v (or use a car...

... assembly plugs into one of the top USB ports on the RPi and rests its weight on the minimal housing. The printing with the switch on the side of the RPi is the RPi-Power-Bar (https://www.thingiverse.com/thing:4653267) also by yours truly. ...

The only thing for me was I am using a RPi with RPiHQ camera, which did not fit in this case. It was not tall enough. I had to extend the case 15mm vertically. ###Changes made Also for the Allsky case I made some changes: 1. an external...

... You can choose from three models: normal type, two-layer type, or wall-framed type. The inside is conductive so grounding and earthing are very easy. Check out the TAKACHI website at https://www.takachi-el.co.jp/products/RPI-4 for more information.

I quickly edited my previous design for RPI 4 Original model is here : https://www.thingiverse.com/thing:4579831

Also, I had a hard time getting the camera cable for my RPI 4 bent around the fan recess so this helps greatly with that 2) Revised venting. This should print easier without support and also work better. With the drawer pushed in, there is venting...

If you ever need a tool to cut holes in a case for an RPi 4, here's a template for the RPi 4 form factor. I purposely made the mounting holes a little small so a fine tipped marker can be used. ... If you want to use a fat marker, just drill the...

Tested with rpi 3 and 4, I power the Pi directly from the PSU.

... Pi to your Anet perfectly with Octoprint! Before adding this part, remember the spacers. To power the RPI, use this: https://www.aliexpress.com/item/DC-DC-Converter-Module-Cable-with-2-USB-Port-input-DC-12V-To-USB-for-Raspberry-Pi/32740430515.html

The C64 RPi TV Mount a Raspberry Pi inside a Commodore C64 and use it with your TV instead of a Monitor. Pros: - Extremely small print size, resulting in less filament usage - Only two USB extension cables are required Cons: - The audio jack is...