rostock max v2 3d models

A 40x40x10 fan shroud is needed to encase a 40x40x10 blower fan. ...A suitable product can be found on Digi-Key under the part number 603-1840-ND.

I modified Solidude's vertical plate mount to accommodate extruders beyond the stock SeeMeCNC EZ/EZR units, and added support for a second extruder in the process. This modification enables you to use a Titan, BMG, or other mount-to-NEMA17 type...

I designed a slimmer fan mount due to enclosure constraints. Three of these mounts are required because the fan blows just off to one side of the nozzle. It was designed specifically to work with this mount for the E3D V6. You can view it here:...

This is an upgraded version of my extruder. This version uses a 3mm screw to attach the bearing to the lever arm, making it much stronger and virtually indestructible. After experiencing a very high failure rate when printing Ninjaflex, I decided to...

I designed a mount specifically for Singh's extruder, which he created to enable printing with Ninjaflex on my Rostock Max V2. ...The extruder is available on Thingiverse at http://www.thingiverse.com/thing:488678.

I'm Installing a Layer Fan Shroud on My Rostock Max V2, Equipped with an E3D Hotend and a Trick Laser LED Light Ring, Without Any Interference from Mounting Screws. Most Fan Shrouds I've Found in the Past Have Been Incompatible with the Trick Laser...

I have a Rostock Max v2 from seemecnc and i had several SKR 1.4 turbo and tft 43 sets laying around so i put together a couple pieces like the magnetic removal bed probe, the fan duct/mount. i have included the marlin 2.0.x files i used for my...

This is my answer to making the Rostock Max V2 effector platform fit seamlessly with the E3D v6 hot end and the Flex3Drive extruder: https://mutley3d.com/Flex3Drive/. I constructed this solution on February 25, 2015. ...Please note that I didn't design...

Fitting a layer fan shroud on my Rostock Max V2, which comes equipped with a stock hotend and a Trick Laser LED light ring, I realized that this design is actually the original. The nozzle extends slightly lower than standard models, giving it a...

This is a functional dual extruder hotend and effector platform upgrade for the Rostock Max V2. The target was to mount two E3D V6 hotends in the original above-the-platform position by creating a new effector platform with a wider center opening.

Modified E3D Dual Mount for RoStock MAX V2; adds clearance for all three M3 SHCS mounting and adjusting 2nd extruder. "Mount 2" reworked for clearance around M3 nylocks. Thinking about incorporating M3 or 6-32 helicoils directly into the part for V3...

This is a mount for dual E3D V6 hotends for the SeeMeCNC Rostock Max V2. I believe it will also fit the V1. One of the hotends is height adjustable for ease of leveling. Included is a single fan shroud. Offset along the Y-Axis only. Required...

This system takes advantage of the original Rambo and LCD controller mounting locations to install a [PanelDue 5"](https://www.duet3d.com/DuetAddons/PanelDue), [Duet 2](https://www.duet3d.com/DuetEthernet) (Wifi/Ethernet), and a [JohnSL FSR Endstop...

Cooling fan mount for 50mm Radial fan (for example http://www.banggood.com/3D-Printer-12V-DC-50mm-Blow-Radial-Cooling-Fan-p-980653.html).\nFan clicks into place and pressure fits snugly - no adhesive needed whatsoever.\nThe design works remarkably...

Summary Mounting a 50mm Radial fan (such as http://www.banggood.com/3D-Printer-12V-DC-50mm-Blow-Radial-Cooling-Fan-p-980653.html) is a breeze with this nifty Cooling Fan Mount. The fan simply slots in and pressure fits, eliminating the need for any...

Dual-Extruder Upgrade Spool Holder Made Easy with SeeMeCNC Panels This project uses standard US hardware, featuring 1/4" threaded rods and 1/20 nuts, because sourcing metric parts in America can be a challenge. If you're not particular about using...

This mounts a NEMA 17 extruder motor and bell housing from the Flex3drive extruder. The motor is attached to a motor bracket point at the top of the printer, orienting the driveshaft for a curved path down to the effector without interference. ...I'm...

This adapter fits over the wooden arm, providing a smooth cylindrical surface for mounting filament spools. Print at least two small locking tabs and securely attach them to the right side of the cylinder to prevent spools from flying off during...

I crafted a holder for a dial gauge to effortlessly calibrate bed height. Check out the specific gauge I utilized below, but numerous others will likely fit. If the gauge hole is too large, two set screw holes are available to secure down the gauge.

When swapping out the RAMBO board for a Duet 2 WiFi, upgrade with ease by adapting the existing board mount. ...Use Seemecnc's file as a starting point and make adjustments to accommodate the new Duet holes, relocating the fan to a central position in...

I couldn't find a shroud that fit my 40x40x20 blower fan, so I modified the standard shroud using the STL provided by SeeMeCNC. I designed it for a snug interference fit between the fan and shroud, which may require light sanding to get a perfect...

The 7-inch screen case is now designed to easily slip into place on the sloping Duex4/Paneldue housing, all without needing any additional tools.

Summary Print strong, but without specific temperature restrictions. This piece fits: https://www.amazon.com/AccuRemote-ELECTRONIC-INDICATOR-Functions-conversion/dp/B006YD7G36/ref=sr_1_25?ie=UTF8&qid=1465888680&sr=8-25&keywords=dial+indicator Attach...

I fashioned it because some of my spindles turned out to be bigger than standard equipment accommodated, providing approximately an additional fifty millimeters of extra room to maneuver.

The mount was custom designed, and fan adapters were based on a specific design found at: http://www.thingiverse.com/thing:715119. It held the e3d v6 firmly in place, and the cooling system proved to be highly effective. The z-axis experienced no...

I've been using FSRs for a year as my zprobe, but they just didn't work as well after much tweaking. I've looked at other various zprobes, including the newest IR ones that didn't work with my PEI bed. The hall-o effect probe seemed too complicated,...

You can get all necessary parts by visiting these online stores: Raspberry Pi Kit: http://www.amazon.com/gp/product/B00MV6TAJI Camera: http://www.amazon.com/gp/product/B00E1GGE40 3D Printer Link:...

... out either. To make it easier to push the LEDs all of the way in, I used the top of a pen which I slide over the wires. Print Settings Printer Brand: SeeMeCNC Printer: Rostock MAX Rafts: Yes Supports: No Resolution: 0.2mm Infill: 100% Custom Section

Print Settings: Printer Brand: SeeMeCNC Printer: Rostock MAX Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.25 Infill: 20 Notes: I used a skirt to print it as I have flatness issues on one side of my delta's print area and the skirt...

... screw and clamp, causing major problems! Luckily, this issue has since been resolved. (Last update: March 3, 2016) Print Settings: Printer Model: SeeMeCNC Print Technology: Rostock MAX Support Generation: No Layer Resolution: .2 Infill Density: 50%