rostock max v2 3d models

Customized version of http://www.thingiverse.com/thing:16627 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: retainer...

Slots are designed specifically for spatulas and putty knives. Small holes accommodate spudgers, probes, and pry bars. Large holes perfectly fit four-ounce medicine dropper bottles used to hold alcohol and acetone slurry. Version 2 can hold a total...

The Summary: This ensures belts stay centered on towers at all times. Nylon was used for the pulley, while PLA spacers were printed separately. To clear the tower, some sanding was necessary for the lower inboard pulley. ...OpenBuilds' 625 bearings were...

To minimize extruder noise, I designed and printed a speedy spacer at full scale with ABS material.

Uh oh! I'm diving into design mode again without wrapping up my previous projects - a bit of a bad habit of mine. Check out this dual hot end mount, specifically the HE280. It requires only minimal modifications to the stock effector platform. I...

The three fan configuration that came with my ball-joint and HE280 hotend upgrade was a huge disappointment when it came to layer cooling, because the fans weren't pointing anywhere near the layers as they were being laid down by the nozzle. I...

I conceptualized an enclosure and, as is often the case, I discovered that timkloss had already designed it. Instead of creating a new design from scratch, I chose to use his model and make some modifications. The entire project was created using...

The indicator, designed for the EZStruder shaft, allows you to monitor extrusion speed and identify filament retraction. ...Constructed with two shells and a 100% infill for durability.

To fix the broken clamp, I sought an alternative method for tightening belts without relying on the pulley jack system. ...To achieve this, I threaded the belt carriage through the clamp and tightened it using a wire tie or two to securely mesh the belt...

This will keep the belts tracking in the center of the towers. I printed the pulley in nylon and the spacers in PLA. The lower inboard pulley required some sanding to clear the tower. I used 625 bearings from here.

Summary This visual indicator attaches to the end of the EZStruder shaft, providing a clear view of the extrusion speed and filament retraction status in real-time. ... Instructions Crafted from two shells and built with 100% solid infill for maximum...

A personalized version of http://www.thingiverse.com/thing:54024 was created using Customizer! (http://www.thingiverse.com/apps/customizer/run?thing_id=54024). ...The specifications include HoleDiameter = 6.2, KnobDiameter = 13, HoleFlatThickness = 1.5,...

I've retired this version and introduced an updated one. The post where the bearing attaches to the lever arm can become weakened and break off after several hundred hours of printing. I've modified the design to utilize a 3mm screw to secure the...

Customized version of http://www.thingiverse.com/thing:16627 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: idler_ht...

E3D V6 Titan Extruder Mount for the Rostock Max 3D Printer - SeeMeCNC

The Threaded Filament Dust Filter, originally designed by ppyromann, can be easily attached to the upper part of a Rostock MAX 3D printer for enhanced dust filtration.

Print Settings Printer Brand: SeeMeCNC Printer: Rostock MAX Rafts: No Supports: Yes Resolution: 0.5mm nozzle; 0.2mm layer height Infill: Doesn't Matter Notes: I printed the cover with PLA using supports everywhere. The retention clip, on the other...

This fan duct can be used on both Rostock Max v1 and v2 models, ensuring smooth airflow for either variant. Simply attach your 30mm fan securely with screws, and you're ready to go! ...PLA prints work fine if you only print in PLA, but if you switch to...

Here are the exact Upper and Lower mounts for 626Pilot's Hall-Theta Z-Probe, designed to fit perfectly in place of those used for Rostock Max models, which now have an added feature - three strategically aligned mounting holes.

Top Panel for the enclosure mod for the Rostock Max v3 here:http://www.thingiverse.com/thing:1796438 Equipped with two powerful 40mm fans to expertly blow over the Rambo board Print Settings Printer Brand: SeeMeCNC excels in producing high-quality...

... customized according to your preference, as there is ample material provided. This part can be printed with full infill and easily attached to the Rostock Max platform arms without any issues. ...Customization options are available for a better fit.

For your Rostock Max Square Bed, address the issue of a non-flat Polycarbonate build surface top by using this design. ...Normal clips may not fit well, but printing two copies of this at 1.0 size, one on each side, will resolve warping and raising...

This is a detachable side panel designed specifically for the SeeMeCNC Rostock Max V3 with a Dual 60mm fan grill and mounting system. It's ideal for anyone looking to add cooling capabilities to parts of the printer obstructed by the panel. ...The...

This modified Rostock Max layer fan is designed specifically for use with an E3D V6 hot end and 626Pilot's superior mount, available at http://www.thingiverse.com/thing:137140. ...The standard layer fan sits too low when paired with the 'tall' mount.

The original file was printed, but modifications were made to suit the Rostock Max Idler bearing. The belts needed adjustment, and upon reinstalling the bearing, tightening the belts, and recalibrating, the print could be finalized. ...Changes included...

This is a custom side panel designed specifically for the SeeMeCNC Rostock Max V3, featuring a single 60mm fan grill and mount that adds essential cooling to the printer's often-overlooked areas. ...Modeled directly from the official SeeMeCNC GitHub...

http://www.themakerhive.com/shop/viewitem.php?productid=41 Print Settings: Printer Brand: SeeMeCNC Printer: Rostock MAX v2 Rafts: No rafts were used Supports: Supports are not needed for this print Resolution: The resolution is set to 0.2mm for a...

This is an easy-to-make two-drawer insert designed specifically for the base cabinet of a SeeMeCNC Rostock MAX V3 3D printer. The concept was inspired by my friend Chris, who deserves all the credit for coming up with this brilliant idea - I...

Just use a 12mm tube (a carbon fiber tube is pictured) between the two stock towers on the Rostock Max. I put some tape on the end to ensure the filament spools didn't slide off. ...You could also print a 12mm tube, but it's best to use something...

... to the printer. The original metal spacers can be used, and a flat area is provided for fan mounting between two arms, ensuring clearance. Remember to adjust XYZ max height and test for clearances before running the Rostock without head movement.