rostock max v2 3d printer

Fitting a layer fan shroud on my Rostock Max V2, which comes equipped with a stock hotend and a Trick Laser LED light ring, I realized that this design is actually the original. The nozzle extends slightly lower than standard models, giving it a...

This is a functional dual extruder hotend and effector platform upgrade for the Rostock Max V2. The target was to mount two E3D V6 hotends in the original above-the-platform position by creating a new effector platform with a wider center opening.

Derived from RepRap.me's innovative Diamond Hotend mount by Kharar, some crucial measurements have been reverse-engineered from SeeMeCNC's iconic Rostock MAX Delta 3D printer. This will require a strategic print process to avoid complications -...

Modified E3D Dual Mount for RoStock MAX V2; adds clearance for all three M3 SHCS mounting and adjusting 2nd extruder. "Mount 2" reworked for clearance around M3 nylocks. Thinking about incorporating M3 or 6-32 helicoils directly into the part for V3...

... out either. To make it easier to push the LEDs all of the way in, I used the top of a pen which I slide over the wires. Print Settings Printer Brand: SeeMeCNC Printer: Rostock MAX Rafts: Yes Supports: No Resolution: 0.2mm Infill: 100% Custom Section

This is a mount for dual E3D V6 hotends for the SeeMeCNC Rostock Max V2. I believe it will also fit the V1. One of the hotends is height adjustable for ease of leveling. Included is a single fan shroud. Offset along the Y-Axis only. Required...

This system takes advantage of the original Rambo and LCD controller mounting locations to install a [PanelDue 5"](https://www.duet3d.com/DuetAddons/PanelDue), [Duet 2](https://www.duet3d.com/DuetEthernet) (Wifi/Ethernet), and a [JohnSL FSR Endstop...

... holes for mounting are 4mm in diameter. A press-in nut with a 3mm ID and 5mm OD will be used on the other side of the dial indicator. Printer Settings: Printer Brand: SeeMeCNC Printer: Rostock MAX Rafts: No Supports: No Resolution: .2mm Infill: 50%

Print Settings: Printer Brand: SeeMeCNC Printer: Rostock MAX Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.25 Infill: 20 Notes: I used a skirt to print it as I have flatness issues on one side of my delta's print area and the skirt...

Create an easy-to-print, 40mm fan duct for your Rostock Max 3D printer using OpenSCAD. ...Print it in PLA without needing support material, then secure it to the platform with three cable ties threaded through its top holes and air outlets (as shown in...

... a custom drawer to utilize the unused space on my Rostock Max v3's front panel, perfect for storing my tools within easy reach. ... Print Settings Printer Brand: SeeMeCNC Printer: Rostock MAX Rafts: No Supports: Yes Resolution: 0.15mm Infill: 15%

Create an enclosure for your Rostock 3D printer using 12x24" sheets of 1/4" Acrylic. This will prevent drafts and warping of large parts while also serving as a demonstrator at events with children and adults. To assemble, print the provided...

The spool has an outer diameter of 8 inches, a width of 3 inches, and a hole for the spindle measuring 7/8 inch (0.875) to fit on the acrylic clothes-pin spindle provided in the kit. Photos will be added upon printing and installation. This is a...

The initial Jetpad design was remarkable, but it had an issue where the first genuine layer was printed mid-air. ...To rectify this, a subsequent version of the model was created with the offending minor vector eliminated, ensuring a level base layer.

My second 3d printer

... for them. I shortened the leads from the LED ring and got rid of the quick connector on the power wires. Print Settings Printer Brand: Rostock Printer: Rostock Max V3 Supports: Yes Resolution: .15 Infill: 10% Notes: print with tabs facing up

This thing was created using Tinkercad. Edit it online at https://www.tinkercad.com/things/eycrLGiHuCE. I designed this to mount the unused 30mm PLA blower fan so that it points directly at the extruder stepper hobbed gear, which had gotten too hot...

This clamp is designed to fit snugly against the glass plate, remaining low and flush to prevent interference with layer fans or the nozzle itself. It's built with the FSR Mount Plate in mind, as designed by Michael Hackney at...

A 40x40x10 fan shroud is needed to encase a 40x40x10 blower fan. ...A suitable product can be found on Digi-Key under the part number 603-1840-ND.

I don't own the rights to this content and didn't create it, but I couldn't locate a file for it on Thingiverse, so I simply uploaded it. ...If anyone believes this is copyrighted material or something similar, please leave a comment and I'll remove it...

<p>I got magball arms so tried putting the Duet SE carriage adapters straight on the Molded Cheapskate Carriages. Worked ok, but there was just too much flex with the carbon fiber arms. If you look at the 2nd photo it compares the joint locations for...

The spool holder's flat surface at the top prevented the extruder from smoothly pulling in filament, causing the machine to abruptly jerk each time. ...That issue was effectively resolved.

Remixed Solidude's vertical plate mount to allow for extruders other than the stock SeeMeCNC EZ/EZR units, and added support for a second extruder while I was at it. This will let you use a Titan, BMG, or other mount-to-NEMA17 type extruder unit.

I modified Solidude's vertical plate mount to accommodate extruders beyond the stock SeeMeCNC EZ/EZR units, and added support for a second extruder in the process. This modification enables you to use a Titan, BMG, or other mount-to-NEMA17 type...

I designed a slimmer fan mount due to enclosure constraints. Three of these mounts are required because the fan blows just off to one side of the nozzle. It was designed specifically to work with this mount for the E3D V6. You can view it here:...

The build area is not a perfect circle and doesn't resemble one at all. This image only shows part of the build area, leaving about 1-2 cm of space around it. This object excels at testing your X/Y/Z tower endstop calibration because it utilizes...

The spool holder's flat top ensured that every time the extruder drew in filament, the machine would experience a slight tug. ...By designing it this way, engineers eliminated the jerking motion that had been a recurring issue.

Customized Version of Thingiverse Thing 54024 Created with Customizer http://www.thingiverse.com/apps/customizer/run?thing_id=54024 Instructions Using the following Options: Taper Percentage Set to 30 Knob Height Set to 14 Shaft...

I needed to get my layer fans working again after many modifications to my hotend mount. I found that I had three 30mm box fans sitting around, but all the shroud designs I could find were either for 30mm squirrel-cage fans or 40mm box fans. So I...

This design is a revised version of http://www.thingiverse.com/thing:1936202 . The original file did not allow enough clearance for the LED light with wires soldered to it to slide in at all. Affordable and effective, the lights used can be found...