romex spool holder 3d models

Make a spool holder using a screw and nut. I have a specific bearing that's hard to find, so I'll share it with you - feel free to use or modify it with your own design and bearing. ... **Print Settings** * **Printer:** My Delta printer * **Rafts:** No...

The steel shaft is a tight press fit to the sides of the spool holder, I used a mallet and hammered them together. ... Printed Parts: 2 each Part_A 2 each Part_B 1 each Part_C (optional) 8 each Shaft_Spacer Other Parts: 4 each - 5x 8*30*10mm Nylon...

This spool holder is perfect for use with aluminum-profile 3D printers and other similar 3D printers that feature a vertical surface area to attach it to. It's specifically designed to fit spools that are about 90-95 mm in diameter, as well as the...

Two spool holders are used with a 10mm nut on each side, so the spool won´t move sideways on the axle and turning the spool causes the axle to spin. While printing the filament is unrolling and moving the spool along with the axle and the nuts. There...

The spool holder is designed to fit perfectly onto the printer frame, just like the original one. By lowering its center of gravity and shortening its pivot point, it significantly reduces vibrations and oscillations. This design change also brings...

Standalone spool holders are needed in pairs for a complete setup. Each holder measures 80mm in length and must be accompanied by four high-quality ball bearings with dimensions of 7x14x5mm. Print Settings: Printer: Vertex K8402 Rafts: No raft...

Create two identical spool holders for your 3D printer using 1/2" magnets, a piece of schedule 40 3/4"ID pipe and 6-32 1/2" flat-head (countersunk) screws. Attach the holders to a metalic base by placing the magnets on the pipe without any bearing.

I needed a simple spool holder next to my printer so that the strand wouldn't bend or cause stress on my extruder. I designed this using OnShape and all you need to buy are some small skateboard bearings from Amazon (bearings included). I made this...

looked for a spool holder that dident have over 3-5 part couldn't find one so made my own 3 files base spindle and cap reduces the stress on the feed gear and feed angle drastically would get a loud clicking from the driver trying to pull the heavy...

You may need to adjust these to fit your spools. 

Holds/dispenses 5 Spools of 1.18mm (3/64in) cord

Up to 36 inches of spool width is available.

This is great for spools of all sizes. STL is for Bambu spools but can be resized to fit any and all spool sizes as shown in the picture with the Inland spool.

Here's your customized spool: I've put together a custom spool with some fantastic features. ...Using the following specifications: Unit size: 1 inch Spool hole diameter: 1/4 of an inch Spool width: 5 and one-quarter inches

this will hold the spool centered on the outside roll. ...dimensions based off of polymaker filament spool.

It's actually possible to use the spool holder without any bearings, just using B_R parts, but it will have a little more friction. There should be a M8 washer between every part on the threaded rod. Alternatively, you can print an all plastic...

There are spindles in various sizes to allow spools with large holes to rotate smoothly. Joiners for Multiple spool holders There is a joiner to link two spools in series for winding filament from one onto the other. Also a joiner to link spools...

I designed a hex pattern spool holder. It holds the 5 and 15 lb spools from COEX, I'm sure it'll hold plenty of others. I included the F360 files for both the frame and the Dowel as well. The design was centered around the use of 40mm OD bearings...

This is my working version of a spool holder. it uses bearings from a Traxxas RC car and linear rods from a Prusa 3d printer. Bearings below. ...you need 4 of the spool piece of and 2 of the end caps....

ENG:Easy to print, easy to assemble Spool holder.This is just the thing, on which the spool sits.You need:2 x Filamentholder-Screw1 x Filamentholder-Corpus After print, you just screw the three parts together. Screws diameter: 19 mmCorpus...

My first spool holder design that requires no support and mounts with wood screws. I had fun designing this one and was inspired by a piston rod from an engine. It has been tested with a 1 kg spool and can be mounted in various positions. This is...

They created this spool holder using Tinkercad, and they're incredibly proud of their work - so am I! They wanted to add a personal touch, so they included their initials on the inside of the vertical arm in embossed form. We printed these at 10%,...

... to print two of these and glue the boss on the spacer end into the pocket on the opposite side of the second one. you will also need to cut a wooden dowel of piece of PVC to rest the spool on in the cradles built into the top inside of the prints.

Hello, I designed this self supporting spool holder for one of my printers, FlyingBear G5, which it had a weak one. The hole in the middle permits to fix it with a M5 screw everywhere you wish. NOTE: the one in the picture is an old version of the...

End brackets for a spool holder, used with 5/8" dowels. Edit: I originally had this listed as 3/4" dowels, as that's the bin I was pulling them from at the hardware store. I think their bin is mis-labeled, as I get 5/8" when I measure them. The first...

I had lots of problems (like most people did) with the printed bearings from https://www.thingiverse.com/thing:3893905 so I've remixed the spool holder from https://www.thingiverse.com/thing:3209211 to fit the center of the base of the first one I...

Headed out to grab a lattice design spool holder, really intrigued by the concept and confident it'll fit snugly on a 3/4-inch thick surface due to the clip part's 20.10mm gap, slightly larger than 3/4 inch, allowing for tolerances to be cleared with...

I had lots of problems (like most people did) with the printed bearings from https://www.thingiverse.com/thing:3893905 so I've remixed the spool holder from https://www.thingiverse.com/thing:3209211 to fit the center of the base of the first one I...

Thus, having the possibility of loading any type of filament having only one "rechargeable" spool. In this link you can find the operation of the same: https://www.youtube.com/watch?v=-cU5tN7aB8U Se busco la manera de aligerar y mantener una...

My latest acquisition, a cutting-edge 3D printer, arrived sans spool holder, prompting me to devise an innovative solution of my own. This straightforward design requires no support material during printing, making the process a breeze. I strongly...