romantic couple silhouette 3d models

I tried to print a couple of different versions of this style of puzzle, but I had no luck… One puzzle fell apart while trying to solve it, while the others fused parts together. Despite attempts to adjust my flow rate and scale the model, I was...

I found a couple of great models on GradCAD from Yauhen - Lego Skeleton Minifig Fantasy Era and Classic Lego Skeleton. These included the STEP and SLDPART files, so I could easily modify them and export with high enough resolution for...

The robot has a ponderous gait.   PrintingGenerally I use a 0.25mm layer height and put about 1mm of plastic on the outside surfaces as a shell.  Since my printer has a 0.5mm nozzle I use 2 vertical shells and 4 horizontal top and...

Couple Bands: Elegant duo bands, available in diverse metals and adorned with stones to symbolize unity. Casual Bands: Stylish and minimalist design for everyday wear. Suitable for modern and sleek appearances. Cocktail Bands: Edgy yet...

I bought this: https://www.aliexpress.com/item/EiBotBoard-board-eggbot-drawing-machine-main-control-board/32789757886.htmlIt arrived in a couple of weeks and I'm ashamed to say the way that the black circuit board coordinates with my white printed...

Note that the NeoPixel Rings tend to arrive with the remains of perforated 'tags' on a couple of the sides. It may be necessary to file them off. ### Cloned Hardware This project is intended for an original Adafruit NeoPixel Ring and original...

Theoretically this distance should be the combined 2 radi of the pitch diameters of the two gears, however in practise, the actual proper distance can differ from a few fractions of a mm to a couple mms, due to manufacturing inaccuracies, as well as...

I hate wobble and I also got the feeling that prints seem to have shrunk very slightly after a couple of days, making the connection a bit looser. For me, the required clearance varies between 0 and 0.1 mm, depending on the filament.</p><p>If you...

Therefore I want to couple Hotend-fan controller (const. at 50%) with Nozzle-fan cooler (min. to 100%) with two diodes in parallel (in RTN line). Results in diagram picture. I decided to use 58% minimum and increase to 80% after 4th layer. -...

I've had good luck with this battery for the most part, but have had a couple of times when I needed to fully charge it up to work with the iron. I've run the ts-80 for about 10-15minutes off the Anker QC 3.0 battery, and not had a problem with it...

Keep using those ties or a couple of small M4 bolts that can be tapped using your fingers into the Prusament Spool, see appropriate holes in the photograph attached..If you suspend the spool from a tree or other object then a large plastic tie (or...

There're a couple things you can configure before flashing your Arduino: rf24_rx[5] - Is a 5-character channel that is the unique id for each puck, for individual addressing. Give each puck a unique number but leave the first three characters...

Fixes and Improvements The source model is great, but it had a couple of fickle issues. The first is, when assembled, the EM drive section had some noticeable gaps along the seams due to the waffle pattern of grooves along the underside which...

(if no cable is included with the end stops) A firmware to compile yourself (I used this here: https://github.com/davidramiro/Marlin-Ai3M-2.0.x) The Arduino IDE (https://www.arduino.cc/en/main/software) and a couple of printed end stop holders /...

Probably a good idea to print a couple of the mounts. It's easy to screw it up when adding the brass inserts. You'll want a piece of PTFE tubing between your extruder and the radiator. Measure the depth of your radiator, and the depth of your...

  If you cannot get the wire installed, STOP and investigate the print, since it should not take a great amount of force to install the wires, and you may have an issue with the print which is blocking the holes for the wire hinge.  Do not push too...

If you look at photo #3, you can see that the entire rectangle has cutting marks on it– and there are a couple spots where I wasn't careful enough and took out some chunks. That's not a huge problem though, as it'll just result in bits of exposure...

Hand sketch the outline of the ship on paper from the side - I'm considering doing a front/back view for a couple ships for added stability. 3. Scan/Document Camera the sketch to get a jpeg 4. Open the jpeg with Gimp/Photoshop 5. Use...

They aren't really required - they just provide some more protection. In addition to the printed parts, you will need the following: 1) 1/4-20 threaded rod, 3" length 2) 2 1/4-20 nuts 3) 2 M6-1.0 hex bolts 16mm length 4) 2 M6-1.0 hex bolts 30mm...

There are 12 couples of wheels, so 24 wheels in total.There are solar panels on the roof of the IMC, and there are deployable solar panel fabric solar panels on the sides of the IMC. In the undeployed state they are rolled up on top of the IMC, in...

Finally – If you are going to fly it: EDIT: Use a C6-3 Print out a couple of lugs (included in the STLs) and glue them – align them for your launch pad. Go over the edges of the lugs that are touching the tube with another bead of glue after the...

Wait a couple of days, verify the leveling and adjust the position.I upgraded my MK3S+ to MMU2S adding extra weight on the already heaviest part of the printer. I use 6 balls and may add an extra one.</p><h3>Print instructions</h3><p>PETG is supposed...

2/13/2022: The prototype fuse's are done, Ive added some new pictures of these and a few sneak peaks of a partially covered model which should be finished within the next couple days. I've opted to go with the tissue paper and paint covering method...

(DESIGNER'S NOTE-- A few of these pieces were delicate prints when split, though this could be due to printer issues, so a couple of files may change slightly in the near future, but if it works fine for you, then go for it..--) We've set up a...

The list of parts you will need is as follows:An Arduino-based microcontroller (Arduino Pro Micro in my case)A real-time clock module (DS3231 or similar)A TowerPro MG995 continuous rotation servo motorA standard LEDA standard light-dependent resistor...

Placing a couple of these back to back makes the middle spacer for the large and small frame connector bolt. Don't glue them together, they rotate against each other. Pipe clip - Print as needed. This is just a handy 3/4" pipe clip if you want...

=========================================================== __Update: May 9, 2021__ A quick update on our progress and a couple more pictures. You can see the two Dyna-Soar nose cones next to each other. As the original nose on the left needed to be...

Almost forgot Material flow rate, now this will play a part in a couple areas. First it will affect your tolerance between parts, surface quality (all sides top, bottom and sides), and adhesion of the layers and to the bed. If you surface are uneven...

Notes: - I printed all the parts lying down with supports and the panels seem strong and turned out pretty well - I left the supports on the body panels to add strength and to provide a surface to mount inside panels like the old school vinyl on...

This version is included for those that want to create a custom playing field using other materials.Other Printing NotesWhile I was able to get pretty good results printing the sidewalls without supports, I did get better results adding a couple of...