roller shade 3d models

Models for Implementing a Homemade Curtain for Aqara Roller Shades

for when your roller shade is a little too short

The roller shade made of straw is actually a product that is widely available at 100 yen shops.

... dc motor, I built these motorized roller shade openers for my parents on request. ... The full blog post here: https://philsprojects.wordpress.com/2021/02/28/motorized-roller-shade-opener/ https://youtu.be/VtMDJMMf43Q https://youtu.be/B7FsTKy4AMA

... shade openers for my parents on request. ...The full blog post here: https://philsprojects.wordpress.com/2021/02/28/motorized-roller-shade-opener/ Print Settings Rafts: No Supports: No Resolution: 200 Infill: 20 Filament: PolyMaker PLA Category: DIY

Using a wemos d1 mini, h-bridge motor controller, and geared dc motor, I built these motorized roller shade openers for my parents on request. The full blog post here: https://philsprojects.wordpress.com/2021/02/28/motorized-roller-shade-opener/ ...

My software project for this undertaking can be found here: https://github.com/mrcory/Roller-Shade-Controller Note that the gears labeled "(Alternate Ratio)" have an approximate ratio of 2:1 instead of the intended near 1:1 ratio. ... A huge thank you...

If the print fails print again ASAP to maintain some heat on the build platform. For more information go here http://helpme3dprint.com/blogs/news/13574710-3d-print-a-roller-shade-end-plug The filament used in this print came from...

For more information go herehttp://helpme3dprint.com/blogs/news/13574710-3d-print-a-roller-shade-end-plug The filament used in this print came from http://www.ORDSolutions.com The amazing 3D printing software used in this print can be purchased at...

Parts to fit an Aqara SRSC-M01 tubular motor inside a 51mm roller shade tube.

My roller blinds sometimes got stuck behind the Roller Shade Driver E1. This guide is to prevent that.It is mounted behind the base plate, using the same screws.

I wanted to use a smart motor to control my roller shades. But the chain loop was too long for the motor to be placed in the window sill. I didn't want to cut the chain loop, plus the connector that connects the 2 ends of the chain was too big to...

Broke the plastic part which allows me to crank my patio shade curtain up and down. This replacement is printed in ~1hr in PETG and fits perfectly. ...

 The solution was to build a thicker plate to receive the pin, thus closing the gap and holding the shades more securely.   The fusion model is attached and is fully parameterized. ... The settings in the picture above match the STL that is uploaded for...

... ends of the bottom rail of Coolaroo Outdoor Roller Shades. Bungee tie downs loop through the rings and secure the roller shade in the Bungee receivers. ... More info here: https://shop.coolaroousa.com/19mm-tube-end-cap-with-ring-sand-z-11-brcs

The brand was "StyleWell Cut-to-Size Cordless Room Darkening Vinyl Roller Shades" model UVRD6G7378AA sku 1004459997 internet 309076207. ...Sometimes they are listed as "unbranded" but they typically all use the same mounting bracket which is...

Roller Shade Model: https://www.homedepot.com/p/iFit-Cut-to-Size-Dark-Gray-Cordless-Blackout-UV-Protection-Roller-Shades-45-in-W-x-73-in-L-47026/308304067 Note that the roller shades I have are slightly thicker than usual, causing issues with the...

Human: I had Hunter Douglas Roller Shades installed on my doors but they came with flimsy plastic clips that were hard to work with. I created these to take a 60mm x 10mm x 5mm Neodymium magnet so the shades would automatically stay in place when...

Roller Shade Model: https://www.homedepot.com/p/iFit-Cut-to-Size-Dark-Gray-Cordless-Blackout-UV-Protection-Roller-Shades-45-in-W-x-73-in-L-47026/308304067 Note: I found that my roller shades are slightly too thick to use the motor cover from the...

It may still work fine if you plan on not rolling up all the way. Remixed from the original Fusion360 project to fit the roller shades I have. These are the roller shades:...

Once the roller shade is set at the desired position, fix it in place by tying off the lift cords to an appropriate cleat (many are available on Thingiverse). If your shade is long, use two cleats per shade, spaced vertically apart. The very long...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/hGLENzy6NGV

Bandalux roller shades are combined with the wide array of fabrics and colors, they fit perfectly into the architecture of the building and ensure excellent sun protection, while guaranteeing the desired visual comfort, in keeping with the selected...

Replacement for the broken end cap on our Hunter-Douglas Roller Shades. Holding mechanism is stronger than the original parts, so it takes a little force to put in place, but holds much better. ...

I use the wire to power Somfy roller shades (never have to change batteries). I terminated each wire in the window frame using this 3D printed jack. I added a cover for windows that won't have shades right away. This 5.5mm x 2.1mm jack fits in the...

I was missing the end cap to my Sundance Window Coverings roller shade and created this.

Components for blinds with 43mm tube and Aqara SRSC-M01 Smart Roller Shade Controller.

I've created a parametric pulley specifically for the Aqara roller shade driver E1, and I've included STL files for pulleys with 6 to 18 teeth. The speed of the shades is directly proportional to the number of teeth on the pulley. ...To pull up the...

Modified henryarnold's files to work seamlessly with my 35mm inner diameter Bali roller shades and the same EY2512 motor he utilized successfully. Printed in PETG on an MP Select Mini at 50% infill, with precision and care. Currently still working...

... support center post works with the new end support. It snaps right into the new part. The 38 mm Roller Shade Motor: http://www.amazon.com and then search for "B01DZQ43AI" BOFU is the brand of this motor and remote kit. Category: Replacement Parts