roller chain sprocket 3d model

This helps with the strength of the threads as it will be printed length wise on the build placeThis gives more freedom to place pieces in any orientation, as well as add spacers between larger parts for more accents and individualityFixed stringing...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 34 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

NOTE: all models are at initial stage and not refined, nor optimized for printing, only a rough idea at the moment The unmanned colony builder/Mars MkI is a project that seeks to automate the construction of shelters and basic facilities that a...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 0...

I hope this piece works for you; it was actually the most challenging to model and get right. 9. You should be good to reassemble now! 10. Put the hammer-trigger-piston assembly back in. 11. Lay the cylinder back in place, including the U-clip for...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

This model will do the same stuttering if printed too fast even with the used a reduced segment count (50) in the cylinders. The trusty SD card worked for me with a big batch of these. The other solution was to slow the print down.Let me know in...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

is ASVFSVF14K203 [US] [CA].----------------PrintingThe “ALL.stl” file prints the entire set of models you'd need to assemble ONE power plug housing. Separate STL file for each of the part is also provided for your...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_top_port_corner_resolution = 8 custom_back_camera_x_position = 0...

The one thing most existing models seem to be missing is the funky characters on the keys. I looked around and found a font that looks just like what they used (basically an old computer font like the one used at the bottom of checks, ...) As I...

I haven't printed it yet, but the OpenSCAD model turned out pretty well. See the additional .scad file, .stl and the explanatory symbols image. The original bezel is dark grey with a textured interior except for the plinth and label obrounds. This...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protectionSuperior...

The COMPLETE Maneater Nagarots I bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The Nagarots are a cult devoted to the Serpent Demon Yn'aga, herald of the Tyrant-God...

http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: crankSlack = 1.8 times smaller gear_tolerance = a negligible 0.1 inch midAxisHolderH = stands at an impressive height of 6.3 inches noteAlpha =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_width = 100 use_mouse_ears = 1 pattern_element_overlap = 0 stencil_shape = 7 custom_back_camera_y_size = 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

It's also compatible with the Chinese clones of both these models, often referred to as "J-head" extruders. There is a cable guide built into the design which will assist with keeping everything tidy and reduce any stress on the heater and thermistor...

now you can the stands/feet print without support or if you want the texture of the powder-coated pei sheet you can print it on its side without support.Release Candidate 1.5 - 15 January 2021Updated some sections to the model so it's stronger when...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Modeled after a 1915 candlestick phone, early versions had no dial because you just lifted the earpiece and clicked the lever a few times to get the operator's attention and told her the number or person you wanted to speak to. This is a fairly good...

In addition, in case you want to remix you would potentially only have to adapt the holder model.The bottom of the holder has a cavity that exactly fits a specific lightning cable found on Amazon with angled connectors to reduce the space it...

So far my failures are in optimizing the printer tuning to keep the model airtight. As stated in the Harvard paper, they printed a form and molded silicone for the soft actuators. I probably should do that too, but I am determined to work with FDM...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 1 stencil_shape = 6 stencil_size = 40 stencil_mirror = 0 custom_back_extra_port_x_size = 30...

Have fun and use common sense ;) This is my own creation and the model can also be found on Thingiverse thing:3771579 Print instructionsPrinting info: Printed on Prusa i3 MK3S, PLA 0.2mm layers, 4 perimeters for strength, main mount was printed...

I have printed the model in 2 colors with an extruder, changing the color of the filament in Z: 150, except in parts 1,2 and 3 that have part of the roof and I have changed it in Z: 150.02. The dial I have changed the color of the numbers. I bought...

Some photos of the printed mod installed on the machine may differ from the STL due to the fact that my machine is a prototype, and I decided to change some details after discovering potential issues (so I updated the models, but for lack of time, I...

First, I modeled the front of the display to fit the RepRap Discount Full Graphics Smart Controller. Then, I also decided it needed a back to protect the circuit board. Easy peasy! Next, I tackled the problem of mounting a TFT35 touch screen...

Bbut if you have a problem with the fit please provide some feedback, and if possible the flat to flat measurement of the 5/16-18 nuts you are using with this model. Note that if you find that both the nuts and the bearings don't fit, you should...