roland fp 4 3d models

This hook snaps onto the wooden horizontal support under my Roland FP-10. ...No screws are required.

Bracket to hold a 13" MacBook Pro securely on a Roland FP-30 Digital Piano, providing ample room for the device's dimensions. The bracket may also accommodate the slightly smaller FP-10 model, although the laptop might protrude over the piano keys...

A holder for the Roland FP-30 power adapter to mount it easily to the Roland KSC-70 stand.

The Roland FP-30X digital piano comes with a separate power adapter, which ends up in the floor and getting in the way. ...This holder makes it possible to just hang the power adapter on the back of the frame.

... ...It is attached to the Piano Stand KSCFP10. The whole purpose of this is to get rid of all the cables on the floor. For the Roland FP-30 you can use this remix by w00h or this remix by Reiver. Please check out my headset holder for the FP-10. ...

This is a headset holder for the Roland FP-10 piano. A screw from the piano stand KSCFP10 is used to attach the holder to the bottom side of the piano. You can attach the holder on the left side (as shown in the photo) or on the right side. ... Please...

A non intrusive hook for headphones and cables that attaches to Roland KSC-70 stand for the Roland FP-30 / FP-30X. It fits snuggly on the back board of the piano stand. No screws or glue needed. Print at any quality. I tried 0.12 and 0.2, both...

I designed a laptop stand specifically for my Roland FP-90 digital piano/keyboard that holds my HP Omen gaming laptop perfectly. This design may also work for other Roland models; please let me know if you try it, and I will add your experience to...

The Roland FP-10 has no flat surfaces to hold a timer. The crowned rear bar easily sheds my timer due to vibration. My solution is to print a 2 inch by 3 inch platform that is contoured to fit this crown on the bottom and is flat on the top. ...I faced...

Simple holder for USB and audio cables for Roland FP-30. Gadget is connected to USB-A and USB-B port in piano. Supports are necesary only for connection points (you can see in Photo). ... I use PLA Resolution 0.3 Infill 10% Supports yes

Lost my roland fp90x's slider hat, so have to make one. ... Slider hats on FP90 or FP90x are all the same.

... and treble_clef_stand) flat with supports for the lip. ...Print the base vertical with supports. I use the tabs with a dot of hot glue to connect to the stock FP-30 music stand (one under the base and one at the top corner of the back).

I modified the design to accustom the FP-30 PSU and made a few changes for my needs: * the whole design is slightly longer because of the longer PSU * it's mirrored, so the mains cable comes out towards the left leg of the piano when mounted * I...

I modified another design to accustom the FP-30 PSU and made a few changes for my needs:the whole design is slightly longer because of the longer PSUit's mirrored, so the mains cable comes out towards the left leg of the piano when mountedI removed...

Roland 1/4" Jack Nut that fits most Roland Keyboard and Guitar Amps. Confirmed fit on my Roland AC-60 and Roland Micro Cube amp. These nuts are highly non-standard for input jacks. ...The threading is M12x1 Specifically, the matching part is: Roland...

Really simple desktop stand i made for my Roland VT-4. I love this little guy, but i hate the form factor (for desktop use anyway). So I made this stand. ...It can be printed in one piece.

Had a need to have my 13" laptop on my Piano while playing and doing some homework while pursuing a music degree, so I modeled this up real fast in Fusion360 and printed it on a CR10-S5 out of PLA. Putting it out here in-case it can help anyone else...

This model was crafted using 3ds Max 2016 software and then saved in the compatible format for 3ds Max 2013. It is measured in millimeters as its unit of measurement. The rendering process employed Corona v1.7, while V-Ray v3.6 was converted from...

<p>This allows you to attach the pianos power adapter to the back of the KSC-70.</p><p><strong>To Print</strong></p><ul><li>Printed it in PLA</li><li>Layer height of 0.3mm</li></ul>

Note letters that lies flat at the top of the keys, showing what note is what key. Color change at 1 mm, or just add a modifier box for the letters only on a multi-material printer. ... The lip at the top edge is important - otherwise the letters...

roland tent pootje

This is a printing file for my personal dnd character Roland

http://www.thingiverse.com/apps/customizer/run?thing_id=834725 Instructions Using the following options: center = 60 spacing = [12,17.5,14,13,13,13,14.5,14.3,12.5,13,13,12.8,12.5,12,12] Font_name = Pacifico twist = -3 Rotation = 45 height =...

For clarity and coherence, the text is extruded by extruder two Minimal border width remains set at zero for simplicity Bar thickness stands tall at 2.4 mm. Lug-text distance stands steadfast at two units of distance. To avoid aesthetic clutter,...

This Model is Dedicated to My Beloved Friend Roland Schneider

4" lift kit for Roland V-Drums stand.If you're over 6' tall, you will appreciate the lift to the kit. It will make you sit on your throne in a proper ergonomic posture and you won't be banging your hands into your lap or knees into the drum pads.The...

The replacement part for the Harper FP-26 Centrifugeuse 4 in 1 appliance is a versatile adapter ring that serves as a substitute for the original component. This essential piece of equipment enables users to unlock the full potential of their device,...

Full animated simple 4-cycle engine by Roland Schwarz, Germany

The design is for Roland FA-06; I assume it should fit FA-07 and FA-08 too. The bracket requires a couple of rather long bolts. I ended up making my own by running a threading die on some soft steel rod stock. I printed in PETG. It holds up...

... is a Cameo 4 Blade Holder Adapter. ... To use Secabo (maybe Roland types) Blade holders in your cameo 4. ... Diameters of Blade Holder see picture This adapter works great but get gently with Pressure, take 1 for the first Time for Vynil cutting.