rohloff with chain tensioner 3d models

... for a chain. looks nice with the finer links. prints well with .12 to .2 layer hight. Customized version of https://www.thingiverse.com/thing:28405 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=28405

A replacement X-carriage for Tevo Tarantula stock, with integrated X-belt tensioner, dual fan mounts for 5015 blower fans, and auto level sensor mounting points is designed to replace the stock acrylic carriage after it becomes soft and warped during...

This is based on the Wanhao i3 X-Axis Belt Tensioner, designed by Heathicus at Thingiverse. I'm running some IGUS-style printed PLA bushings in an SCS8UU block. The original design placed my bottom belt off-center, causing it to rub against the...

I absolutely love the AndrewBCN remix of my i3 reinforced y-motor.\nThe re-remix was created using FreeCAD with slotted screw holes to allow some tension to be given to the belt once it is attached to the holder.\nThe concept is quite...

I used an M5x35mm screw and a nut for the screw that tightens the belt tensioner. If your belt is not too short, you could probably use a bit shorter screw. In designing this, it looked like the screw would miss the belt, but after printing it seemed...

Key chain with LEGO logo , printed in TPU, very strong keychaincreated with fusion360https://www.thingiverse.com/thing:4728150https://www.myminifactory.com/object/3d-print-key-ring-lego-logo-1502583D printing settingsTPU infill filament 100% 0,2mm...

This design enables you to tighten the lock nut sufficiently to create friction on the arm, preventing it from deflecting upwards when adjusting to your preferred tension setting. ...Additionally, this setup includes an alignment wheel for the bearing,...

Always want a lighter outside? ...This is the thing for you. Print as many chain links as you need. The lighter holder is printed upright as not to bother with suppoert material, the links flat face down so the layers hold better.

Printed the remixed design but found it hard to add water during cleaning. ...Found out I had a small 12V pump laying around with a 8mm inside diameter tube. ...this way water will be sprayed on the chain providing extra cleaning.

I've managed to get idig3d's Y belt tensioner to print multiple times without issue after adding a small amount of material between its legs for extra support.

Changed model of both Prusa MK2.5 and MK3 X end Motor mount. ...It is dedicated to MK2.5 so it is possible to apply a belt tensioner to it.

Changed model of both Prusa MK2.5 and MK3 X end Motor mount. ...It is dedicated to MK2.5 so it is possible to apply a belt tensioner to it.

The Anet A2 Carrier features a block specifically designed to manage the Y-Belt Tension, ensuring precise and smooth operation. ...This versatile carrier also boasts multiple 4mm holes that allow for easy attachment of various accessories or equipment.

... on Thingiverse. ...This design will require scaling by a factor of ten; I'll make the necessary adjustments in my next export. It's recommended to use Adverse Effects' outstanding belt tensioner model, available at www.thingiverse.com/thing:3941721.

... Process of Pushing the Belt In and Expanded the Base for Enhanced Stability Against the Printer Bed. If You're Interested in kmag's Original Belt Tensioner Without the End-Stop Feature, It Can Be Found Here: http://www.thingiverse.com/thing:1436236

I'm completely infiltrated now. ...The PLA is definitely on me.

dia 7mm, thickness 0.5mm) * For the front slider: Tensioner Screw: - 1x Printed knob - 1x M4x25 screw - 2x M4 nuts - 1x M4 washer Moving roller assembly: - 1x Printed front slider - 2x F623ZZ bearings - 1x M3x18 screw - 1x M3 nut - 6x M3 washers *...

A person holds a key chain featuring an iconic transistor emblem.

Quick Remix of Madau3D's Direct Drivinator. ...Adds a bracket for a cable chain attachment.

Siehe --> https://www.thingiverse.com/thing:3811614 ENGLISH: For the MK3/s for Prusa I have equipped the Z-slides with a belt tensioner and a clamping function for the liners. This project is based on "Revised X-Axis (Prusa I3) by vekoj" but is...

Specifically, one upgrade I adopted was the popular Boogie Bear-derived x-axis upgrade. While this worked exceptionally well with my printer's BMG-centric extruder / hotend setup, I recently opted to again upgrade my extruder / hotend assembly to the...

... to add, remove, or replace without having to take everything apart. It was printed at a layer height of 0.2mm with a nozzle diameter of 0.4mm, using two perimeters and 10% infill. ...The bottom layers were set to two and the top layers to three.

Created by a seasoned 3D CAD/CAM expert with extensive experience in Autodesk Maya. Need additional file formats? No problem - just let me know and I'll convert them for you. This model is optimized for game modeling, jewelry store displays,...

I wanted to create a metal case as an alternative to the breakable plastic card holder with a side chain holder hole. If you print this design, please provide feedback on any errors. ...Note: The current model is slightly too large for standard cards; I...

 “Machine With Roller Chain” is a motor-driven sprocket that drives a length of chain up through a table and the chain is allowed to tumble onto itself in a hypnotic and organic motion.    With my version, my goal was to make a...

These are modified,  shorter end connectors for the drag chain designed by Marius Hornberger.  There are two variants available:Variant 1 has two 3mm holes for countersinking screwsVariant 2 has one 4mm hole for a countersinking...

I've designed an undercarriage for four standard LM8UU bearings, integrating a belt tensioner into the Y-belt, with all holes and screws sized for M3 diameter using a 5.5mm nut wrench size. There are two versions to accommodate either the original...

I printed the previous Y-Axis tensioner (https://www.thingiverse.com/thing:2149867) but discovered that the belt section was too tight for my Anet A8 printer. I took the part and widened the section where the belt and pulley system are, giving it...

... the puller so it wouldn't break again after I had to repair it twice. ...You can reuse the standard screw for securing the bearings, eliminating the need for bearing sleeves. Furthermore, I salvaged a knob from a Y-tensioner and put it to good use.

This is the Mendel Z Leadscrew Base w/ Motor Mount and Belt Tensioner built-in, modified to reduce print time and non-printed parts requirement. ... Only one threaded-rod cross-bar is needed to keep the mendel frame stable, so I've modified the original...