roger waters height 3d models

It can create bricks as small as 1x1x1 (plate height) or as large as 48x48x18 (6 normal bricks high). The customizer, by default, creates LEGO-sized bricks only. All dimensions are accurate, but it has a tolerance parameter so the dimensions can...

I printed at a layer height of 0.1mm for just about everything except for parts like the alligner or the large stand. You could make do with 0.15mm or 0.2mm for most parts, though you'd lose some detail on some of the more intricate...

See section Tail feathers remix. Print settingsLayer height: 0.2mmInfill: 10-20% (pendulum weight 100% infill)Seam: All shafts and gears have a small notch for the seam. Make sure when slicing that the seam is placed in that notch (in PrusaSlicer...

Print with 0.15mm layer height, 3 perimeters, zero infill. The “ensure vertical shell thickness” setting should be <strong>disabled</strong> for lightest weight.</p><p>Set a cylinder modifier around the hub with 20% cubic infill, to provide some...

Using the following options: corner_radius = 10 qr_tolerance = 0.001 qr_y = 0 qr_x = 0 corner_num = 0 qr_rotate = 0 tag_thickness = 3 round_corner = 1 tag_width = 80 hole_r = 10 hole_y = 0 hole_x = 30 obj = 0 tag_height = 80 case_thickness = 1.8...

The printer shows me the height it's at while it's printing and as soon as it finishes tag body (the layer at 1.0 mm, by default) I pause it using the menu on the printer control panel. Most printers support the M600 G-code command, so you may be...

Specific ON-ROAD INFO: This version of the KIDS Chassis is for building an On-Road / Touring / Drifting 1/10 3D printed RC Car - It will use short CVDs so the total axle width will be less than 190-200mm - Includes a Universal Body Holding System,...

Print the shells with the flat bottom on the build plate at 0.3mm layer height. You might want to add a 2 or 3 mm brim to keep them attached to the build plate. If so, ensure you cut off the brim with a knife so there is no extra flashing as this...

I can provide alternative parts for this if required.&nbsp;Spring: I purchased a 20mm spring initially which was too long and I cut it down, the 10mm I have is slightly too short so would recommend a 15mm or 20mm and cut if required.&nbsp;DockNote:...

These posts have threaded ends so that using the screws can be screwed into the plates or each other to extend the height. There are four different size posts at present. They are: 48mm, 89mm, 159mm, and 227mm. Yes, they are all short and supposed...

Links to materials: M3x8mm screws Magnets 10x5mm for enclosures Magnets 10x2mm for flywheels Aluminum rod 5 mm Bearings 12x8x3.5 Motor PWM speed controller DC-DC step-down module 5.5mm jack Touch button MOSFET LED Strip Double...

Take your Steiner3D revolver to new heights with the Steiner3D Revolver Mods. Attach suppressors, sights, bayonets, or other accessories using a 1/2 inch threaded barrel and tactical picatinny rails. Enjoy the ultimate customization experience. The...

You can do finer adjustments to the tolerance by putting some scotch tape or masking tape on the inside of the shell wall. Print the shells with the flat bottom on the build plate at 0.3mm layer height. You might want to add a 2 or 3 mm brim to...

The center rail is the perfect height for those that want to mount a DIN rail to mount items to. General Design ==================== I have used parameter based design as much as possible (mounts excluded as they are one-offs, usually only based...

Customized version of http://www.thingiverse.com/thing:46884 with options: hole_r=10, hole_y=0, hole_x=30, perimeter=-1000, qr_rotate=0, code_flip=0, qr_bottom=1, qr_scale=1.6, tag_height=80, obj=0, corner_num=0, qr_data=[0, 0, 0, 0, 0, 0, 0, 0, 0,...

I printed mine using Amazon Basics Black PLA filament with 0.2 mm layer height, 0.4 mm bottom thickness, 0.6 mm top thickness, and 15% zig zag infill. The filament is dark enough that you can't see the infill pattern with those settings. ...

This unit incorporates one center pole to elevate the light head assembly above a 41" mounting height for optimum coverage.Often referred to as simply a "tank light," this unit is considered universal due to its ability to be passed through any...

Instructions: - corner_radius = 10 - qr_tolerance = 0.001 - qr_y = 0 - qr_x = 0 - corner_num = 0 - qr_rotate = 0 - tag_thickness = 3 - round_corner = 1 - tag_width = 80 - hole_r = 10 - hole_y = 0 - hole_x = 30 - obj = 0 - tag_height = 80 -...

They all use the draft profile with the layer heights set to 0.2 mm and the number of top and bottom layers set to 0. The model has an overlap-modifying cutting mesh support blocker sized 136x88x2 at [0,0,0] with 4 top layers and 4 bottom layers...

Here are the options used for this customization: - qr_thickness = 5 - code_flip = 0 - hole_r = 10 - hole_y = 0 - hole_x = 30 - qr_rotate = 0 - tag_height = 80 - perimeter = -1000 - round_corner = 1 - tag_thickness = 3 - qr_bottom = 1 -...

Из за чего приходилось постоянно вытягивать припой второй рукой, что не так удобно и быстро.Parts links below - Материалы которые я использовал: Micro Mini N20 Gear Motor DC 3V -6V Li-polymer 3.7v 200mah 502025 Type-C USB 18650 Lithium Battery...

If this is an issue for you in your use case then remove the mesh and simply scale the spacer ring in the Z direction in your slicer to compensate for the lost height of the mesh. That way the edge of the filter media can be clamped without a mesh...

Many more refinements are certainly possible with a full 3D approach now being used, and further design iterations may be made at a future dateThis new build design includes a ‘normal’ plain base with built-in fittings for various battery power...

Makes it a little easier to work on the converters. Print instructionsThe Parts All parts has to be printed with 0.2 layer height. 0.3 can cause issues. No supports are needed for anything. All parts in the arm is glued together. All parts of the...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: shape =...

ArrowGuideBottom x 3 ArrowGuideTop x 3 RevolverGuideFrame x 2 ArrowSled x 3 StringReleaseHook x 3 StringPulley_Inner x 6 MiniArrow x 3 (or more!) See the Print Settings section below for layer height, supports and infill settings Assembly...

If the part isnt listed here, just print one. ArrowGuideBottom x 3 ArrowGuideTop x 3 RevolverGuideFrame x 2 ArrowSled x 3 StringReleaseHook x 3 StringPulley_Inner x 6 MiniArrow x 3 (or more!) See the Print Settings section below for layer height,...

Do not overtighten the motor mount to avoid damage to the printed parts.Repeat the same step to the front right motor mount.Route the remains of the belts around the front side bearing stacks of the XY joiners on each side, ensure the belts are not...

Cup holder for stroller Anex Sport ENG:Hi all! I made my wife a cup holder for the Anex Sport stroller. She was very happy with it.</div><div>The cup holder is quite strong and compact. For greater reliability, I printed it from plastic PETG. Even...

For the drafts, I used 0.3mm layer height, 10% infill, supports but no adhesion, printing speed 60mm/s, infill speed 80mm/s, outer wall speed 30mm/s, inner wall speed 60mm/s, enable retraction NO, on an Anycubic i3 Mega printer with TPU mod. It does...