rog strix x570 i 3d models

The Strix Goblin HD mount was reworked to accommodate a Swift or Split camera in its nose section. Initially, the Split was tested, but it proved troublesome for installation and removal. Therefore, it was replaced with a Swift. A modified version...

This is a portable hard drive case that I designed based on the ROG Huracan CPU Case.

This is an cover for the amd standard cooler (Wraith) with a Asus ROG look! ... This is not my Design i only added a ROG Logo (Original Designer: Ozkan_Ozturk)

An ASUS ROG Ally stand, remixed from ssulti's original. ...This should fit on a smaller print bed size (I use a Flashforge Adventurer 3) and features logos from the ROG brand.

Some pilots have discovered that the replacement CNC machined aluminum motor mount for the Strix Goblin is slightly loose when installed. This causes a small gap between the motor mount and the aircraft's fuselage, allowing the motor to pivot. This...

I wanted the tray to stay firmly in place, so I reinforced the front spar with additional support.

I was unable to locate a compatible component for the Runcam Split V3 Micro. ...Therefore, I modified the design to make it workable.

I modified the Hero8 battery door attachment to prevent it from flying off during intense landings.

Created from PLA filament, I printed them using an Ender 3 printer with standard settings. To assemble, rotate each part 90 degrees so that the side against the wall is facing downwards. You'll need to print two of these per plane to ensure...

I had to cram the VTX into a tight spot in the back of my quad, so I came up with this outboard mount for my VTX. ...The design was centered around an AKK X1, but it should fit most VTMs with an SMA connector placed squarely in the middle.

... protector can be securely fastened using either clear adhesive tape or a specially formulated, non-toxic foam-safe adhesive. For added convenience, I opted to use clear tape on both the top and bottom edges for effortless removal at any time.

I added that side band to keep the Hero8 battery door from flinging off during crashes. 8/11/20 Added a 30° version of this mount. 12/24/20 Added a new base mount for use with Hero 8 stock standoffs. ... 12/27/20 Updated the stock Hero8 mount with...

I made a little clip with a slight z-bend to hold the two pieces together.----- previous notesI remixed a few mounting options for DJI O3 and Vista in combination with the flight controller Matek 405WMN and 405WSE.The O3 mounting solution allows...

To prepare the tray for assembly, I carefully cut it to size using a jigsaw and then attached it securely to the base plate with hot glue. The LED strips used were standard 12V, 4-pin RGB models. ... Don't forget to give your project a thumbs-up by...

Customized version of https://www.thingiverse.com/thing:4837562 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4837562

Gamer SSD Disk Cover. M.2 Cover. Custom made. ... Any questions please leave them in comments.

Preset on gcode file: MK2.5S 20% infill 0,10mm layer high material PETG color change at 2,60mm Print time 3h35min

The objective of this robot gripper test challenge is an affordable, plastic part, either produced via injection molding or 3D printing. ...This item is specifically designed to avoid compatibility with magnetic grippers and serves as a budget-friendly...

This is a hard case for my Asus ROG Flow Z13 tablet I designed. I couldn't really make it fit the way I intended so am offering it up for general consumption. ... Hope you can use it.

I designed this custom ASUS ROG logo for my laptop and I'm really pleased with how it turned out. ...It was created using Fusion 360, a powerful modeling tool that allowed me to bring my vision to life.

I'm new to 3D modeling, so I'm posting a scan of an Asus Rog Ally so people who know how to do it can make a cool hard case.

GAMING HEADSET HOLDER like the asus rog with phone holder I do not authorize resale of the stl file, or the printed item. ... I can Add your nick name on the object if you ask me.

Couldn't find an existing design for a stand with a fan mount, so I remixed a basic ROG Ally stand and an 80mm fan stand.I also adjusted the stand size so the tolerance is a bit looser and fits the Ally with a screen protector.It's working pretty...

I created this simple bracket to sit atop my ASUS ROG monitor, securing some cardboard in place to block direct sunlight from blasting me in the face each morning.

A Keyboard Leg replacement of Asus Rog Stryx Flare

ASUS ROG logo 3D model made in Blender 3.0

Measurements were taken for my ASUS ROG 3 though it should still work with all other ROG phone models. The front lip has a spot to put the rubber plug so you don't loose it. It uses a 90 degree USB-C extension cable available here...

I received a unique request to replace the standard SSD bracket with a custom ROG RYZEN emblem, which meant covering up the holes on the power supply shroud's bottom plate. ...I gladly accepted this challenge and managed to design a new SSD installation...