robot arm part 3d models
656072 3d models found related to robot arm part.
cults3d
A 3D part can contain a complex design such as a robotic arm useful for different tasks, after being programmed. ...One of the important parts becomes that part.
thingiverse
Robotic arm for each part for 3D printing and assembly drawing for Catia Software. ...This document was created for Robotic subject, BFM4503 based on our learning and goal to move a box from one position to another position
thingiverse
This package contains the design files for 3D-printed parts used to build an electromechanical robotic arm for the Viking robot at Portland State University. The design of these parts was part of an ECE 506 project. ... Three of the parts used are from...
thingiverse
Designed in 2013 as spare components for the robot arm kit used in the Science Olympiad competition, these parts were created using OpenSCAD software.
thingiverse
A test part of an underactuated modular robotic arm skeleton. ...It can be manufactured by 3D printing and can be printed with as few supports as possible.
grabcad
/*still in development*/It is planned to be installed on the robotic arm as a general tool module.
thingiverse
usp=sharing Added image of parts that need threading Tools you need: - M4x0.7mm Hand Taps - M3x0.5mm Hand Taps - Adjustable Tap Wrench - 10mm drill bit for bearing housing - 9mm drill bit for MG996R servo arm - 8mm drill bit for bearing housing -...
thingiverse
The following hardware will be needed to assemble the arm: M3 x 8mm round head(22x), 20 used to mount the servo horns (including the gripper) M3 x 10mm round head(34x) M3 x 63mm round head (2x) M3 x 16mm round head (4x) M3 nut (2x) M4 x 16mm round...
thingiverse
This component is the turntable of the robotic arm. The following hardware will be needed to assemble the gripper: M3 x 10mm round head(25x) M3 x 8mm round head (8x) M3 x 3mm grub screw (1x) M4 x 3mm grub screw (1x) M4 x ...mm (5x), length for bottom...
thingiverse
This component is the gripper of the robotic arm, it is based on the mantis gripper from 4ndreas (thing:1480408). The following hardware will be needed to assemble the gripper: M3 x 25mm round head(2x) M3 x 10mm countersunk (1x) M3 x 10mm round head...
grabcad
The two primary components in question are pullers and bearings, both crucial for smooth functionality in machinery.
thingiverse
These are 3D-printer files needed to build your Turtle Robotic Arm using Maker Kit. 1x RoboticArmFingerL 1x RoboticArmFingerR 4x 01137 4x GSR_04_2 Have fun! ... www.turtlerover.com
thingiverse
This design is made to work with specific electro motors as follows: - The big part with sign MDX is to stay on top of a 2'' linear actuator. - The big quadrat is for a Stepper Motor - 4-wire 200 steps/rev, 12V 400mA - The second big one at the...
thingiverse
This is an overview parts (Joint5 and Joint6) for my 6DOF robot arm. ... The original STL files itself located on github: https://github.com/RoboLabHub/RobotArm_v1.0 Additional details used in these parts: - 3mm bolts and nuts - 693ZZ bearings (3x8x4mm)...
thingiverse
This is an overview parts (Joint3 and Joint4) for my 6DOF robot arm. ... The original STL files itself located on github: https://github.com/RoboLabHub/RobotArm_v1.0 Additional details used in these parts: - 3mm bolts and nuts - 693ZZ bearings (3x8x4mm)...
thingiverse
This is an overview parts (Joint1 and Joint2) for my 6DOF robot arm. ... The original STL files itself located on github: https://github.com/RoboLabHub/RobotArm_v1.0 Additional details used in these parts: - 3mm bolts and nuts - 693ZZ bearings (3x8x4mm)...
thingiverse
Here is the body and arms for the Walk-Stop-Walk robot. You can find that project here. https://www.thingiverse.com/thing:4817294 Video of the build. ... https://youtu.be/py5ykNLkRkc
thingiverse
Custom Section 1669029 - Meccano - Base Parts - Plates Struts Angles 1695615 - Geared MOTORs to Meccano and Lego Conversion - Parts 1695691 - Motorized Robotics Kit - Meccano Lego Compatible Parts 1698141 - Shark Octopus Robotic - Motorized Meccano...
thingiverse
Standards CCSS Overview and Background Build a Robotic Arm Participating teams of three or four students are provided with a bag of printed robot arm parts and pins. Each team must use the materials to design and build a working robot arm. The robot...
grabcad
A simple (home project) CAD model of a robotic arm. ...Each part has been modelled with a servo motor housing in mind, however, no real consideration for wiring.