robo 3d r1 plus

I had to design a spacer to attach this 3D filament out sensor to my Robo 3D R1+ 3D printer. So I snapped a picture of its back and then, using Selva and Tinkercad, I transformed it into a 3D model and then adjusted it to fit perfectly! Total time...

Creating a spacer to mount this 3D filament out sensor on my Robo 3D R1+ 3D printer required some quick thinking. I snapped a picture of the back, then using Selva and Tinkercad, I transformed it into a 3D model and adjusted it to fit perfectly! The...

Enclosure for Orange Pi R1 Plus LTS. No need for support. However, it is beetter to enable supports for the base piece, so the screw head recesses come out better. ... Use 4 M3x12 Waffer Head Allen or Torx screws.

This is a modified version of the Robo R1 Z axis stabilizer clip created by 1nxtmonster. To prevent movement, I sealed off the end of the hole at the end with a secure fit. ... Original File http://www.thingiverse.com/thing:587583

A case for the Orange Pi R1 Plus SoC. The cover is autoclip, no need to glue or screw, comes with a neutral one or the Cheapwall one. The Orange Pi R1+ can be screwed at the bottom using standard 3mm screws This case is part of the Cheapwall...

I made some adjustments to get my titan extruder working with my Prometheus V2. I tweaked the quick release design from http://www.thingiverse.com/thing:1192896 to be thinner because the top channel on the Prometheus isn't as wide as the E3D. I also...

I modified a few parts to get my titan extruder to work with my Prometheus V2. I modified the Quick release from http://www.thingiverse.com/thing:1192896 to be thinner since the top channel on the Prometheus is not as wide as the E3D. I also...

I'm remixing two designs to create a unique fan setup. The first design is based on Thing 1890240 and the second on Thing 1385737. I've added four 6mm holes for 5mm LEDs to give it some extra flair. ...To keep things running smoothly, I'm using a 12V...

I'm going to remix two things from Thingiverse: 1890240 and 1385737. The resulting model will have four holes for 5mm LEDs, making it easy to illuminate the fan. I used a 12V blower cooling fan with a 50x50x20mm footprint, similar to the one sold by...

I redesigned from scratch the extended feet inspired by Ben_R's design. To stabilize my printer, which was slipping excessively due to the direct attachment of PLA feet to a smooth wood desk, I incorporated a recessed area at the bottom to...

I found that the LM8UU bearings would wobble in the factory pillow block due to their being too much play in the bearings. I created a design that will hold the bearings in place much better and gives a tighter fit and has eliminated the wobble that...

Customized Version of Thingiverse Project 735213 Created with Customizer! Thingiverse Apps: Run Customizer Now! ... Instructions Using the Following Options: Tube Diameter Set to 30 Quality Level: High Definition (80%) Arm End...

A tub from Target was split in two. Strong cabinet magnets hold the tub firmly in place, while support straps prevent it from toppling over if bumped into. I noticed another person on this site using this tub design. He employed a different version...

I redesigned the foot to include a mounting screw hole, resolving the issue where my printer kept sliding off the table it sat on. ...To prevent this from happening again, I incorporated a spot to securely attach the feet to the tabletop using a...

Put the orbiter mount on top of the hotend mount, put blower fan mount part A (optional) underneath the x carriage, align them and use two sets of long screw (M4 or smaller) and nut to fix all these parts on the x carriage (I used the long screws and...

Please note that Orange Pi R1 Plus is different and the USB-A / USB-C are swapped in location. ## Changes * Enclosed SD card and reset button. Case is a little wider and deeper to facilitate this. * Redid openings for ethernet/usb to make...

This is a custom version of @TechSupportGo's dual fan mount for the Robo R1, which houses a V6 hotend with a round design. It also features a velocity stack at both the front and rear to enhance airflow from the fan to cool the heat sink. To match...

This is the Titian Aero Extruder Carriage complete setup for the Robo R1+ or R1. It comes equipped with front and back fan mounts, as well as a specialty chain setup that presses onto the Z-axis for seamless operation. Designed to be completely...

The Height-Adjustable ROBO3D Riser Feet feature a thumbscrew design that elevates the entire printer, retaining the utility of the original rubber inserts. ...This updated model draws inspiration from a classic and highly-regarded design found on this...

Original Design: #RoboHemera crafted a brilliant simple carriage for the E3D Hemera extruder. (https://www.thingiverse.com/thing:4043642) Also Check out my remixed fan: https://www.thingiverse.com/thing:4159192 I had a cable chain system that I...

I engineered this tool because I sought a means of fine-tuning the belt tension without relying on a screwdriver. It was printed at full density, with a brief pause incorporated into the G-code to allow for easy insertion of the M4 jam nut. ...To...

A R1 rim modeled to specs.For more car-related objects, please do visit my profile.Enjoy! ...

Now the Oiler slides around on the top.\nPrint Settings\nPrinter Brand: \n Robo 3D\n \n Printer: \n R1 ABS + PLA Model\n \n Rafts: \n No\n \n Supports: \n Yes\n \n Resolution: \n 0.2mm\n \n Infill: \n 25%\n \n Notes: \n Printed with PLA at 210C and...

This is a fully realized 3D cityscape modeled after American cities, built on a real-world scale. The entire scene is set up and ready for rendering with all materials configured in Vray. Lighting is achieved through the use of HDRI and Dome light.

Here is a printable extruder shroud for your R1 ROBO 3D Printer. Cleans up the extruder look and gives your ROBO 3D printer an all around sleeker feel. ...Requires support, but easy to break away!

ROBO 3D Badge

... guide. Print Settings Printer Brand: ROBO 3D Printer: R1 ABS + PLA Model Rafts: None Supports: None Resolution: Medium Infill: 25% Notes: It should be pretty easy to print, and it prints in less than 20 minutes depending on your printer settings.

Print Settings: Printer Brand: Robo 3D Printer: R1 ABS + PLA Model Rafts: No Supports: Yes Resolution: Medium Infill: 0.25% Notes: Printer: ROBO 3D R1 Plus Infill: 0.25 Extruder temp: 210 Bed temp: 55 Layer Height: 0.2 First Layer Height: 0.3 No...

... cool! I also uploaded a revised version of the tool holder, which is basically just rearranging some stuff to better organize it. Print Settings: Printer Brand: Robo 3D Printer: R1 ABS + PLA Model Rafts: No Supports: No Resolution: .2 Infill: 25%

... just lying around, so I figured they could be repurposed as a Stepper Motor Cooler. ...This should work out pretty well for my Robo 3D R1 and maybe even fit on the Kickstarter model, too - it looks like it'll fit right on the X axis stepper motor.